Używane maszyny z Niemiec - Strona 35 | Innovac GmbH

Innovac GmbH Used machines from Germany

Przykład Centrum Obróbcze

Innovac maszyny-uzywane

Najnowsze oferty [681 - 700 of 3113]

Śrutownica

Munk + Schmitz Problast 80 DV

Niemcy

nieznany

używany

na żądanie

INNO31902

A mobile Munk + Schmitz vacuum blast machine is available. Blast head diameter: 103mm, blast nozzle diameter: 8mm, effective blast pattern width: approx. 30mm, pressure vessel volume: 60l, abrasive capacity metallic/non-metallic: 200kg/100kg, max. abrasive grain size: 1.6mm, filter area: 21m², dust separation efficiency: 99.9%, machine dimensions X/Y/Z: approx. 2050mm/750mm/2300mm, weight: approx. 550kg. An on-site inspection is possible.

Skojarzona elektrociepłownia

Mtu GC 201 N5

Niemcy

2012

używany

na żądanie

INNO31901

Heating output: 275kW, electrical output: 201kW, fuel: natural gas, engine: MTU E 3066 L3, engine cylinders: 6, overall efficiency: approx. 82%, generator rating: 276kVA, machine dimensions X/Y/Z: approx. 3550mm/1800mm/2100mm, weight: approx. 4500kg, operating hours: approx. 57557h. Documentation available. An on-site inspection is possible.

Ciężarówki z platformą

Man TGM 18.330 4X2BL

Niemcy

2007

używany

na żądanie

INNO31900

Max. load capacity: approx. 18t, drive configuration: 4x2, drive type: rear-wheel drive, emission standard: Euro 4, engine displacement: 6871cm³, engine power: 240kW, max. torque: approx. 1250Nm, suspension: leaf suspension at the front, air suspension at the rear, including loading crane. An on-site inspection is possible.

Centrum obróbcze CNC

Hurco VMX 50

Niemcy

2006

używany

na żądanie

INNO31896

Offered is a Hurco CNC vertical machining center including spare parts. Travel X/Y/Z: 1270mm/660mm/610mm, table dimensions X/Y: 1500mm/660mm, max. table load: approx. 1360kg, spindle speed: 10000rpm, spindle taper: SK40, main drive power: approx. 18.5kW, tool pockets: 24, feed X/Y: 30m/min, feed Z: 20m/min, rapid traverse X/Y: 30m/min, rapid traverse Z: 20m/min, spindle operating hours counter: approx. 7676h, control: Hurco Ultimax. Machine dimensions X/Y/Z: approx. 3300mm/2800mm/3000mm, machine weight: approx. 9000kg. Inspection possible by arrangement.

Maszyna bliźniacza

Se-ma SSK65ET

Niemcy

nieznany

używany

na żądanie

INNO31894

A Se-Ma meat grinder and bowl cutter combination machine is available. Bowl cutter volume: approx. 50l, bowl diameter: 940mm, upper edge height on bowl cutter side: 820mm, knife heads: 6, grinder plate diameter: 130mm, feed bowl internal dimensions X/Y: 600mm/820mm, feed bowl external dimensions X/Y: 630mm/850mm, upper edge height on grinder side: 1040mm, machine dimensions X/Y/Z: approx. 1800mm/1050mm/1400mm, weight: approx. 500kg. The machine is not equipped with a mixing gear. An on-site inspection is possible.

Frezarka CNC

Deckel FP5CC

Niemcy

1990

używany

na żądanie

INNO31893

A Deckel CNC universal milling machine is offered. Travel X/Y/Z: 700mm/600mm/550mm, quill stroke: 80mm, milling head swivel range: +/-90°, spindle power: 12kW, max. spindle speed: 6300rpm, feed torque X/Y/Z: 13Nm/13Nm/21Nm, feed rate X/Y/Z: 6m/min, rapid traverse X/Y/Z: 6m/min, tool holder: SK40, measuring resolution: 0.001mm, 4th axis resolution: 0.001°, max. slide load: 1000kg, number of T-slots: 1, T-slot width: 14H7mm, mounting holes for table accessories: M12, control: Deckel Dialog 11. Machine weight: approx. 3900kg, electrical cabinet weight: approx. 475kg, 5110mm/4654mm/2335mm, floor space X/Y: approx. 6200mm/5700mm, floor load: 3500kg/m². Documentation available. Inspection by appointment possible.

Maszyna do formowania, wypełniania i uszczelniania

Pcs MP AF-080-Servo

Niemcy

1997

używany

na żądanie

INNO31892

A PCS vertical form fill seal packaging machine is available. Documentation available. An on-site inspection is possible.

Maszyna do łączenia forniru

Kuper FW 1150

Niemcy

1990

używany

na żądanie

INNO31889

A Kuper zigzag veneer splicing machine is offered. Overhang: 1150mm, working width: 1150mm, veneer thickness range: approx. 0.3mm-3mm, feed rate: approx. 10-30m/min, feed drive power: 0.55kW, working height: approx. 980mm, machine dimensions X/Y/Z: approx. 2160mm/780mm/1650mm, weight: approx. 540kg. Documentation available. Inspection possible by appointment.

Dozownik

Scheugenpflug LP 804 20/20

Niemcy

2023

używany

na żądanie

INNO31888

A Scheugenpflug material preparation and feeding unit is available. Two-component Scheugenpflug LiquiPrep LP804 20/20 machine, year of manufacture: 2023, tank volume: 50l/20l, machine dimensions X/Y/Z: approx. 1500mm/800mm/2050mm, weight: approx. 430kg, operating hours: 0h. The machine is as new and still in its original packaging. Documentation available. An on-site inspection is possible.

Prasa do gięcia krawędzi CNC

Eht EHPS-11-30

Niemcy

1991

używany

na żądanie

INNO31887

Hydraulic CNC press brake EHT for sale. Press force: 1100kN, bending length: 3050mm, min./max. table-ram distance: 280mm/600mm, rapid approach speed: 100mm/s, working speed: 2mm/s-8mm/s, return speed: 100mm/s, backgauge adjustment range: 5-1000mm, backgauge adjustment speed: 200mm/s, backgauge vertical adjustment: +/-10mm, safety distance between tooling and operating elements: 120mm, stopping time: 75ms, stopping distance: 11mm, Control system: DAK 90. Machine weight: 8500kg. Documentation available. Inspection by appointment possible.

Maszyna do szczotkowania i gratowania

Spontan HBE-90-2000

Niemcy

2026

używany

na żądanie

INNO31886

A brand new Spontan brush deburring machine, which was used only as a demonstration machine, for tubes and profiles is available. Product length range: 100mm-2000mm, Product diameter range: 8mm-90mm, Brush diameter: 300mm, Wall thickness range: 0.5mm-6mm, Max. workpiece weight: 10kg/m, Min. product length: 2×diameter, Brush wire diameter range: 0.2mm-0.5mm, Brush length: 450mm, Discharge height: 1300mm, Machine dimensions X/Y/Z: approx. 3500mm/1750mm/1700mm. Documentation available. An on-site inspection is possible.

Centrum toczenia i frezowania CNC

Traub TNX 200

Niemcy

2023

używany

na żądanie

INNO31885

An unused Traub CNC twin-spindle turning and milling center with peripheral equipment is available. Spindle types 1/2: D76/D76, max. turning length: 900mm, max. workpiece diameter: 76mm, number of tool carriers: 3, control system: Traub TX8i-s V8. Main spindle bore: 76mm, taper size: 6, hollow clamping cylinder: D76/20, indexing: 2.5°, clamping pressure range: 8bar-75bar. Counter spindle bore: 76mm, taper size: 6, hollow clamping cylinder: D76/20, indexing: 2.5°, clamping pressure range: 8bar-75bar. Upper tool carrier: axes: X/Y/Z, stations: 12. Lower left tool carrier: axes: X/Y/Z, stations: 12. Lower right tool carrier: axes: X/Y/Z, stations: 12. Including Isi Elbaron RON4DHEC mist extraction and filtration system, custom-built circulation conveyor, Bürener hinged belt chip conveyor, Bürener Eco-Fluid coolant system (600l), cooling unit, coolant chiller, Traub WH workpiece handling system, various grippers and gripper pairs, IoT, and management and monitoring software. This machine was never put into operation and is therefore in as-new condition. Documentation available. An on-site inspection is possible.

Zawór zwrotny

Vag Top-Stop

Niemcy

2021

używany

na żądanie

INNO31884

Two identical VAG diaphragm check valves are available. Nominal size: DN350, pressure rating: PN10, max. operating pressure: 10bar, max. operating temperature: 50°C, medium: water (1st stage filtrate), face-to-face length: 800mm, flange outside diameter: 505mm, flange thickness: 30mm, bolt circle diameter: 460mm, weight: approx. 280kg. Including two flange-to-flange pipe sections. Both items were only in contact with 1st stage filtrate in a drinking water treatment plant. Documentation available. An on-site inspection is possible.

Centrum obróbcze CNC

Matsuura H.Plus-405

Niemcy

2010

używany

na żądanie

INNO31880

A repair-required Matsuura CNC horizontal machining center is offered. Travel X/Y/Z: 660mm/660mm/660mm, feed rate X/Y/Z: 60m/min, rapid traverse X/Y/Z: 60m/min, number of pallets: 2/6/12/24/36, pallet size X/Y: 500mm/500mm, max. pallet load: 400kg, max. workpiece diameter: 700mm, max. workpiece height: 850mm, max. spindle speed: 12000rpm, spindle power: 15/22kW, max. torque: 187.3Nm at 1120rpm, tool interface: SK40/BT40/HSK63, tool magazine: 60-530 tools, max. tool diameter: 80mm/150mm, max. tool length: 350mm, max. tool weight: 10kg, tool change time: 0.9s, control: Fanuc Matsuura G-Tech 31iB. The machine is integrated into an automation line. The loading-side door is missing. Broken auger for transverse chip transport from the machine bed to the main chip conveyor. The machine is available from calendar week 37. Inspection by appointment is possible. Established machine-tool terminology such as horizontal machining center, tool interface, tool magazine, rapid traverse and rpm has been used.

Maszyna do cięcia plazmowego CNC

Zinser 3825

Niemcy

1999

używany

na żądanie

INNO31875

A ZinserCNC plasma cutting machine is offered, max. plasma capacity: 130A, max. plasma material thickness: approx. 25mm, max. oxy-fuel material thickness: approx. 200mm, cutting table dimensions X/Y: approx. 2750mm/10500mm, working area X/Y: approx. 2000mm/9000mm, X/Y drive: rack and pinion, control: Zinser CNC 500. Inspection possible by appointment.

Centrum obróbki stomatologicznej CNC

Imes-icore Coritec 350i

Niemcy

2015

używany

na żądanie

INNO31872

A 5-axis dental CNC milling and grinding machine from imes-icore is offered. A-axis: 360°, B-axis: 115°, axis inclination with 98mm blank: A-axis/B-axis: 30°/25°, max. machining area: 94mm/30mm, blank holder: 98.5mm, workpiece holder: 1 blank, max. spindle speed: 60000rpm, spindle power: 1.0kW, tool holder: 6mm shank, tool changer: 20, tool length measurement: ≤0.002mm, control system: Logosol 5-axis. Machine dimensions X/Y/Z: approx. 758mm/790mm/857mm, weight: approx. 180kg. Inspection by appointment possible.

Maszyna do cięcia wzdłużnego i prostowania

Bfw/grossmann Sonderbau

Niemcy

2023

używany

na żądanie

INNO31869

A custom-built slitting and straightening machine Grossmann/BFW for aluminum strip is available. Strip width: 35mm, Straightening unit: multi-roll, Knife type: rotary knives, Strip guidance: roller guidance, Tension control: KTC800A. Documentation available. An on-site inspection is possible.

Tokarka CNC

Index V300

Niemcy

2004

używany

na żądanie

INNO31868

Two identical Index CNC lathes including peripheral equipment and accessories are available. Main spindle: D90/Size 8, max. main spindle bore: 90mm, max. workpiece diameter: 340mm, max. workpiece length: 450mm, max. workpiece weight: 100kg, speed: 4200rpm, power: 35.5kW, torque: 550Nm, front bearing diameter: 140mm, clamping stroke: 32mm, clamping pressure: 80bar, travel X/Z: 1500mm/340mm, rapid traverse: 30m/min, feed force: 8kN, tool stations 1/2: 10/10, mounting plate dimensions X/Y: 300mm/490mm. Including coolant system, tool holders, clamping equipment and angle toolholders. Documentation available. An on-site inspection is possible. Expected to be available from autumn 2026. Individual sale possible.

Maszyna do cięcia laserowego CNC

Amada LC2414 Alpha IV NT

Niemcy

2010

używany

na żądanie

INNO31866

A CNC laser cutting machine Amada is available. Laser type: CO2, laser power: 4kW, connected load: 43kVA, max. sheet dimensions: 1500mm/3000mm, max. sheet thickness steel/stainless steel: 10mm/12mm, control system: Fanuc, power-on hours: 34401h, operating hours: 21713h, cutting hours: 11111h. Including loader and unloader. Documentation available. An on-site inspection is possible.

Polerka przelotowa wibrościerna

Walther Trowal ZM 03-FL/MV 21

Niemcy

2017

używany

na żądanie

INNO31865

A compact Walther Trowal vibratory finishing system is available. 1) Walther Trowal ZM 03-FL process water treatment system, Year of manufacture: 2017, Throughput: approx. 1000l/h, Drum capacity: 14l, Acceleration: 2012g, Wastewater tank: 300l, Process water tank: 150l, Compound savings: 90%, Water savings: 98%, Machine dimensions X/Y/Z: approx. 1400mm/1200mm/1750mm, Weight: approx. 600kg, Control system: PLC. 2) Walther Trowal MV 21 vibratory finishing machine, Year of manufacture: 2017, Max. usable capacity: 130l, Ceramic media/plastic media filling capacity: 230kg/150kg, Max. workpiece dimensions diagonal: 570mm, Speed: 3000rpm, Working bowl diameter: 616mm, Working bowl depth: 470mm, Machine dimensions X/Y/Z: approx. 1250mm/1050mm/1200mm, Weight: approx. 900kg, operating hours: approx. 913h. Documentation available. An on-site inspection is possible.