Used machines Germany - Innovac GmbH

Innovac GmbH Used machines from Germany

i.e. Machining Center MORI SEIKI

Innovac used-machines

Latest Offers [1 - 20 of 3101]

Folding Machine

Eurofold T 435

Germany

2008

used

on request

INNO32370

A Eurofold T 435 folding machine in need of repair with a second unit for cross folding is offered. Main machine: A3 folding machine with 4 folding plates, second folding machine: A3 with 2 folding plates. Equipment: electric A3 folding plate set, counting and spacing unit, A2/A3 pile feeder, A3 angled conveyor, standard machine table, electric stream delivery, Becker compressor 25ccm, electric cross-fold folding plate set, L roller conveyor and cross-fold machine table. Motor, pumps, blower and electronics are technically in working order. The polyurethane on the rollers has leaked out, so the rollers must be replaced. Documentation available. Inspection by appointment possible.

CNC Woodworking Machines

Homag BOF 20/60/14/K

Germany

1996

used

on request

INNO32369

Working area X/Y: approx. 6000mm/1400mm, operating voltage: 380V, frequency: 50Hz, rated current: 60A, control voltage: 220V/24V. The machine is fully functional. An on-site inspection is possible.

Air Compressor

Mahle MSK-G

Germany

1999

used

on request

INNO32368

Operating pressure: 350bar, max. final temperature: 120°C, compressed air receiver capacity: 17l, operating pressure of compressed air receiver: 11bar, operating hours: 30,857h, an on-site inspection is possible.

CNC 5-Axes Machining Center

Licon LiFLEX II 766 i³ DT B22

Germany

2016

used

on request

INNO32367

A Licon 5-axis CNC machining center with double trunnion is offered. Travel X/Y/Z: 750mm/660mm/650mm, rapid traverse X/Y: 60m/min, rapid traverse Z: 90m/min, spindle distance: 750mm, motor spindles: 2, max. spindle speed: 12000rpm, spindle power: 37kW, max. torque: 100Nm, tool holder: HSK-A63, tool positions: 96, max. tool diameter: 250mm, max. tool length: 400mm, control: Siemens SINUMERIK 840D sl, automatic mode operating hours: approx. 40148h. Including double trunnion with two torque-driven B-axes, coolant system, MQL system, high-pressure through-spindle coolant and tool identification. Motor spindle 11 was replaced in 2024 and motor spindle 12 in 2023. Commissioning: 2017. The machine was dismantled and preserved at the end of 2024 and is currently in storage. Documentation available. An on-site inspection is possible.

Stationary Concrete Pump

Putzmeister BSA 1004E

Germany

1994

used

on request

INNO32366

An on-site inspection is possible.

Container Washing Machine with Blower

Mohn KW-1800

Germany

2012

used

on request

INNO32365

Suitable containers: E1, E2 and E3, capacity: 125-250crates/h. The system is suitable for the food industry. The system was used very little. The function was checked repeatedly and most recently tested again for full functionality. Before sale, the system will be thoroughly cleaned again. An on-site inspection is possible.

UNIMOG

Mercedes Benz 425 (U1500)

Germany

1981

used

on request

INNO32364

Class/vehicle type: semi-trailer tractor and tractor unit, body type: closed, color: green, curb weight: 6.084t, gross vehicle weight: 10.6t, max. permissible axle load axle 1: 6.2t, max. permissible axle load axle 2: 6.2t, drive type: diesel, max. speed: 95km/h, power: 110kW, displacement (P1): 7675cm³, rated speed: 2600rpm, stationary noise level: 90dBA, engine speed for stationary noise measurement: 1950rpm, mileage: 235,340km, with documentation. An on-site inspection is possible.

Universal Milling Machine

Reckermann 1300 Kombi

Germany

2020

used

on request

INNO32363

A CNC universal bed-type milling machine is offered. Table setup area: approx. 1300mm, operating hours: approx. 100h, spindle hours S1: 54h, program run time: 159h, control: HEIDENHAIN TNC 320, operating voltage: 400V, total rated current: 50A, fuse rating: 63A, spindle speed: 32-1400rpm, control: HEIDENHAIN TNC 320. Equipped with full enclosure, coolant system, work area lighting, chip guard. Weight: approx. 4500kg, overall dimensions X/Y/Z: approx. 3500mm/2000mm/2200mm. Inspection by prior arrangement is possible.

Vacuum Packaging Machine

Henkelman Falcon 80 KL

Germany

2011

used

on request

INNO32362

Vacuum pump capacity: 100m³/h, final vacuum: 99.98%, vacuum chamber: aluminum, housing: stainless steel, power: 3.5kW. Machine dimensions X/Y/Z: approx. 900mm/820mm/1070mm. The machine is fully functional and has no gas flush system. Documentation available. An on-site inspection is possible.

Blister Packaging Machine

Hamer BPC-23

Germany

2018

used

on request

INNO32361

Materials for blister packaging: PVC + coated PVC, PETG + PETG, PET GAG + PETGAG, PS + Complex, operating mode: intermittent, max. output: 12cycles/min, forming film width: 180-350mm, max. forming film diameter: 400mm, max. forming film thickness: 500µm, film transport tolerance (motor): +/-0.2mm, forming area: 150-310x100-210mm, max. sealing pressure: 950kg, max. punching pressure: 10,000kg, max. forming depth: 60mm, sealing temperature: 80-200°C, vacuum pump power: 0.75kW, vacuum pump capacity: 20m³/h, forming heater power: 4.8kW, air consumption: 34m³/h, connected load: 13kW, length: 5530mm, width: 880mm, height: 1460mm, with documentation, Videojet 1520 continuous inkjet printer and Lauda Ultracool UC-0080 recirculating chiller. An on-site inspection is possible.

Paternoster

Hänel Lean-Lift 1300-825/281/164/75/300/40

Germany

2021

used

on request

INNO32360

A vertical Hänel storage lift system is offered. Machine dimensions X/Y/Z: approx. 2810mm/1645mm/6152mm, access height: 890mm. Equipment: 10-fold optoelectronic height measurement of stored goods, integrated protruding goods check at the front and rear, LED lighting above the access point, equipment for emergency operation as well as earthquake-resistant design. Power supply cable: 5 × 2.5mm² / 5 × 4mm², depending on the electrical configuration. Documentation available. An on-site inspection is possible.

CNC Machining Center

Gustav Weeke OPTIMAT BP 140

Germany

1999

used

on request

INNO32359

Spindle nose: A11, turret: VDI60, voltage: 380V, rated current: 153A, fuse protection: 160A, control: Philips B2T, one tool position for boring bars is defective, no driven tools, without chuck, with documentation and maintenance records, the machine was mechanically overhauled in 2010. An on-site inspection is possible, available from mid-December 2026.

CNC Lathe

Oerlikon Boehringer VDF 400 C-U

Germany

1985

used

on request

INNO32358

Spindle nose: A11, turret: VDI60, voltage: 380V, rated current: 153A, fuse protection: 160A, control: Philips B2T, one tool position for boring bars is defective, no driven tools, without chuck, with documentation and maintenance records, the machine was mechanically overhauled in 2010. An on-site inspection is possible, available from mid-December 2026.

2-Axis CNC Lathe

Takisawa EX-122

Germany

2008

used

on request

INNO32357

X-axis: 330mm, Z-axis: 1650mm, max. swing over bed: 910mm, swing over cross slide: 560mm, distance between centers: 1820mm, standard turning diameter: 450mm, max. turning diameter: 610mm, max. turning length: 1650mm, bar capacity: 184mm, spindle speed: 12-1200rpm, spindle nose: A2-15, spindle bore: 200mm, spindle bearing diameter: 266mm, turret type: T10, square tool height: 32mm, boring bar holder diameter: 65mm, tailstock travel: 1400mm, quill stroke: 200mm, tailstock taper: MT5, tailstock quill diameter: 160mm, rapid traverse X-axis: 20m/min, rapid traverse Z-axis: 24m/min, jog feed X-axis: 0-1260mm/min, jog feed Z-axis: 0-1260mm/min, spindle motor power: 30/37kW, X-axis servo motor: 4kW, Z-axis servo motor: 7kW, hydraulic pump: 2.2kW, lubrication pump: 0.004kW, coolant pump: 1.1kW, connected load: 52kW, coolant tank capacity: 300l, hydraulic tank capacity: 83l, lubricating oil tank capacity: 4l, length: 4740mm, width: 2130mm, height: 2090mm, weight: 11t, with documentation. The machine was commissioned in 2008 and operated in single-shift production only, it is currently no longer in operation and has been idle for approx. 2-3 years. An on-site inspection is possible.

Diesel Fork Lift

Linde H35 D

Germany

1984

used

on request

INNO32356

Load capacity: 3.5t, permissible gross weight: 10500kg, operating hours: approx. 4538h. An on-site inspection is possible.

CNC Machining Center

Matec 30HV

Germany

1999

used

on request

INNO32355

Travel X/Y/Z: 2000mm/600mm/800mm, rapid traverse: 30m/min, feed rate: 30m/min, max. spindle speed: 9000rpm, tool holder: SK40, tool positions: 48, clamping plate: 650×2500mm, control: Bosch Type 3 OSA. Documentation available. An on-site inspection is possible.

CNC Milling Machine

Fehlmann PICOMAX 100 CNC

Germany

1991

used

on request

INNO32354

Travel X/Y/Z: 850mm/435mm/210mm, vertical head adjustment: approx. 590mm, table dimensions X/Y: approx. 1570mm/500mm, max. table load: 250kg, spindle taper: Fehlmann SF32, max. spindle speed: 7100rpm, spindle power: approx. 5kW, drilling capacity in steel: 30mm, tapping capacity in steel: M20, control: Mach3 with touchscreen PC, weight: approx. 3000kg. The machine was subsequently retrofitted with a Mach3 control. An on-site inspection is possible.

Cutting Line

Perfecta 168 TS / ZTS 2750 / BASA 7 / BA 6

Germany

2013

used

on request

INNO32353

1) Perfecta 168 TS high-speed cutter, cutting width: 1680mm, usable rear table length: 1680mm, max. clamp opening: 165mm, min. residual strip: 26mm, max. clamping force: 60kN, table height: 890mm, operating hours: approx. 15813h, total cut counter: 349265cuts, weight: approx. 6900kg. Including material hold-down, turning saddle, six carbide knives and five knife cases. 2) Perfecta ZTS 2750 gripper transport system for automatic feeding of the high-speed cutter via the rear table, max. travel: 2750mm, max. clamp opening without/with adapter: 165mm/135mm. 3) Perfecta BASA 7 automatic jogging machine, max. sheet size: 1260×1670mm, min. sheet size: 550×660mm, max. stack height: 1400mm, grammage range: 60-300g/m², feeding from the right or left possible. 4) Perfecta BA 6 unloader, max. size: 1050mm×1450mm, max. layer height: 160mm, max. stack height: 1400mm, max. load capacity: 300kg. Equipped with 15inch touchscreen, USB and Ethernet interface as well as direct processing of prepress data on the machine control without additional hardware, CIP 3 ready, CIP 4 optional. Including spare parts package with wear parts. External compressed air connection with 6bar required. The system is in very good condition. Sale preferably as a complete system. Documentation available. An on-site inspection is possible by appointment.

Injection Moulding Machine

Krauss Maffei KM 350-1400-390 CZ

Germany

2005

used

on request

INNO32352

Max. locking force: 3500kN, clear tie-bar spacing: 710x710mm, min. mold height: 380mm, max. opening stroke: 1300mm minus mold height, max. ejector stroke: 250mm, max. ejector force: 95kN, ejector retraction force: 48kN, rotary table diameter: 890mm, screw diameter K1: 60mm, K2: 35mm, nozzle radius: 15mm, max. injection pressure K1: 2000bar, K2: 2429bar, max. shot weight (PS) K1: 618g, K2: 142g, hot runner: external, core pull connection: DNP Flatface BG3 (large flat-face sealing), centering mandrel: AS + DS, weight: 16.37t, total operating hours: 74,276h, production hours: 66,341h, the second injection unit and the rotary table have not been used for five years, with documentation and linear handling system, regularly maintained in-house. An on-site inspection is possible, the machine is not connected to power.

CNC PCB Drilling and Routing Machines

Pluritec / Schmoll / Lenz Multistation V3/A-System 1 Twin/G650-4/GX-460/2/DLG 550-2 AL

Germany

2001

used

on request

INNO32351

Five CNC PCB drilling and routing machines are available. 1) Pluritec Multistation V3 CNC PCB drilling and routing machine, year of manufacture: 1998. 2) Schmoll A-System 1 Twin CNC PCB drilling machine, year of manufacture: 1997. 3) Lenz G650-4 CNC PCB drilling and routing machine, year of manufacture: 2001. 4) Lenz GX-460/2 CNC PCB drilling and routing machine, year of manufacture: 1991. 5) Lenz DLG 550-2 AL CNC PCB drilling and routing machine, year of manufacture: 2002. The machines come from the drilling department of a PCB manufacturing facility. An on-site inspection is possible.