Maszyny Uzywane Niemcy - Innovac GmbH

Innovac GmbH Used machines from Germany

Przykład Centrum Obróbcze

Innovac maszyny-uzywane

Najnowsze oferty [1541 - 1560 of 3053]

Spawarka TIG

Rehm INVERTIG PRO 350 AC/DC compact / 450 DC

Niemcy

2013

używany

na żądanie

INNO29934

A Rehm Invertig Pro 350 AC DC and a Rehm Invertig Pro 450 DC are available, used and in good condition. 1) Invertig Pro 350 AC DC, standards: IEC 60 974-1 IEC 60 974-2, welding current range TIG: 3-350A, output voltage U₂ at maximum current: approx. 24V, open circuit voltage U₀: approx. 91V, duty cycle 100 percent for TIG at 350A, mains voltage input: three phase 400V 50Hz, protection class: IP23S, protection category: S, setting range: 3-350A for TIG in this AC DC version, duty cycle 100 percent at 40°C 350A for TIG 100 percent duty cycle, input fuse protection: 32A at 3x400V for the 350 AC DC version, length: 520mm, width: 360mm, height: 460mm, weight: 29.5kg for AC DC version. 2) Invertig Pro 450 DC, standard: IEC 60 974-1, welding current range TIG: 3-450A, output voltage U₂ at maximum current: approx. 28V, open circuit voltage U₀: approx. 91V, duty cycle 100 percent at 450A TIG, lower for electrode welding approx. 60 percent, mains input: 3x400V 50Hz, protection class: IP23S, duty cycle at 100 percent 450A TIG at 40°C, electrode welding current approx. 360A at 100 percent duty cycle for electrode in the 450 DC version, input fuse protection: 32A at 400V three phase for 450 versions, length: 520mm, width: 360mm, height: 460mm, weight: approx. 28kg. An on-site inspection is possible.

Maszyna do piaskowania

Mhg SRA-D1H/D3A-BFS

Niemcy

2020

używany

na żądanie

INNO29931

Cabin dimensions X/Y/Z: 3500mm/3500mm/2500mm, door dimensions X/Y: 2800mm/2200mm, small door dimensions X/Y: 1000mm/2000mm, illumination: approx. 750Lux, rotary table diameter range: 1000mm/2500mm, max. workpiece height: 300mm, max. table load (centered): 300kg, horizontal stroke: 2800mm, vertical stroke: 400mm, nozzles: 3. Pressure blasting pot volume: 200l, operating pressure: 8bar, deduster air volume flow 1: 1800m³/h, filter area 1: 17m², deduster air volume flow 2: 3600m³/h, filter area 2: 30m². Overall system dimensions X/Y/Z: approx. 3660mm/3660mm/2650mm, control: Siemens KTP700. Documentation available. An on-site inspection is possible.

Spawarka mag

E/d/e Format M 354 W

Niemcy

2013

używany

na żądanie

INNO29930

10 identical welding machines are available. Fuse protection: 32A, welding range: 40-350A, open circuit voltage: 18-43V, switch steps: 20, welding current at 100 percent duty cycle (40°C): 260A, length: 900mm, width: 560mm, height: 950mm, weight: 120kg. Standards: EN 60974-1 IEC 60974-1 international standard for arc welding equipment, protection class: IP23, protection against spray water and solid foreign objects smaller than 12mm, suitable for outdoor use, insulation class: H, cooling method: AF air cooling with fan, welding current range: 40A 16V to 350A 31.5V, open circuit voltage U₀: 18-43V, duty cycle at 350A: 50 percent duty cycle 5 minutes welding 5 minutes pause, at 330A: 60 percent duty cycle 6 minutes welding 4 minutes pause, at 260A: 100 percent duty cycle continuous operation possible, mains supply voltage: 3~400V 50Hz three phase, maximum mains current I₁ max: 25A, effective mains current I₁ eff: 18A. They are in good condition. An on-site inspection is possible.

Układ sprężarki

Atlas Copco GA45 VSD+/GA45 VSD FF/FX15

Niemcy

2020

używany

na żądanie

INNO29929

A Rico compressor system consisting of two Atlas Copco compressors, two refrigerant dryers and an Atlas Copco Beko oil-water separation system is available. Screw compressor Atlas Copco GA 45 VSD+, year of manufacture: 2020, air volume flow: 9.4m³/min, operating pressure: 13bar, motor power: 45kW, motor speed: 4500rpm, machine dimensions X/Y/Z: approx. 1200mm/1100mm/2000mm, weight: approx. 860kg. Screw compressor Atlas Copco GA 45 VSD FF, year of manufacture: 2012, power: 45kW, operating pressure: 18.5bar, speed: 3000rpm. 2x refrigerant air dryers Atlas Copco FX 15, air volume flow: 15m³/min, operating overpressure: 13bar, pressure drop: approx. 0.3bar, refrigerant: R410A, refrigerant charge: 2050g, max. inlet air temperature: 60°C, machine dimensions X/Y/Z: approx. 900mm/750mm/1000mm, weight: approx. 160kg. Compressor management system Atlas Copco Equalizer 4.0/ES6-MK5, control range: 2-6 compressors. Oil-water separation system Beko ÖWAMAT 15, throughput range: 6m³-30m³/min, oil outlet: DN40, container volume: 115.5l, filling volume: 84.3l, oil collection container: 2x10l, max. operating pressure: 16bar, machine dimensions X/Y/Z: approx. 1100mm/550mm/800mm, weight: approx. 40kg. System operating hours: 8656h, controller hours: 42334h. Documentation available. An on-site inspection is possible.

Sprzęt spawalniczy

Ewm Ag Tetrix 300 Comfort Puls

Niemcy

2021

używany

na żądanie

INNO29928

20 identical welding machines are available. Type: cool41 U31, standard: IEC 60974-1, -2, -10 C.L.A, mains voltage: 400V, frequency: 50/60Hz, protection class: IP23, power consumption P min: 0.9kW, cooling capacity P max: 0.35MPa (3.5bar), max. current consumption: 2.5A, length: 539mm, width: 210mm, height: 415mm, weight: 22kg. Control: Comfort 2.0 with intuitive operation via click wheel, pulse spot normal mode continuously adjustable (especially for TIG welding), pulse pause ratio (balance) adjustable for example from 10-90%, Hz and kHz pulses up to approx. 15kHz, ActivArc technology dynamic arc control to ensure constant performance despite distance fluctuations and to prevent electrode sticking, improved root and penetration quality, spotArc Spotmatic functions for spot welding and tacking, 2-stroke and 4-stroke mode depending on torch trigger operation, manual metal arc welding often with MMA pulse automatic also integrated, gas pre-flow and post-flow times adjustable, upslope and downslope times also controllable, torch modes via torch trigger such as reduced secondary current, memory and job storage recurring welding tasks can be saved depending on version approx. 8-100 jobs, energy efficiency high efficiency, standby function available. Remote control and interfaces remote adjusters and functional torches can be connected, optional LAN WiFi gateway ewm Xnet, PC interfaces for parameter setting and monitoring. Very little used. An on-site inspection is possible.

Wózek podnośnikowy

Linde K

Niemcy

2020

używany

na żądanie

INNO29924

A modular narrow-aisle combination forklift Linde is available. Load capacity: 1100kg, load center: 600mm, wheelbase: 1730mm, lift height: 7200mm, overall height: 4900mm, mast: duplex, transport width/length: 1450mm/3350mm, weight: approx. 8200kg, battery weight: approx. 1600kg, operating hours: 1236h. Documentation available. An on-site inspection is possible.

Skojarzona elektrociepłownia

Kw Energie smartblock 50

Niemcy

2016

używany

na żądanie

INNO29921

Fuel: natural gas (NG), engine: HMG, space heating unit with CHP: yes, condensing boiler: no, additional heating unit: no, low-temperature boiler: no, B11 boiler: no, combi unit: no. Rated heat input P: 88kW, annual efficiency of the space heating system η: 136%, energy efficiency class: A++, usable heat output at rated heat input with additional heater switched off/on: 87.9kW, thermal efficiency at rated heat input with additional heater switched off/on: 57.5%, electrical efficiency at the heat output of the space heating unit with CHP with additional heater switched off/on: 33.5%, auxiliary power consumption at full load/part load el: 1.132kW, in standby mode P SB: 0.06kW, standby heat loss P stby: 0.442kW, annual energy consumption Q HE: 1345kWh, sound power level indoors L WA: 72dB, operating hours: 42,892h. Water was detected in the oil circuit, the unit has an oil-related fault despite sufficient oil being present, and it also shuts down with the message engine too hot. The control unit was overhauled by the manufacturer in 2024, and regular maintenance intervals for oil changes, spark plugs, valves, etc. have been carried out. With documentation.

Nożyce gilotynowe

Darley GS.3016

Niemcy

1975

używany

na żądanie

INNO29917

Max. sheet thickness: 16mm, max. cutting length: 3000mm, weight: approx. 15t. The machine is in good condition. An on-site inspection is possible.

Moduł odwróconej osmozy

Bwt Permaq Compact 51

Niemcy

nieznany

używany

na żądanie

INNO29913

A compact and mobile BWT reverse osmosis system including integrated tank is available. Throughput capacity: approx. 160l/h, recovery (WCF): 40%-75%, salt retention rate: over 98%, permeate conductivity: below 20µS/cm, tank volume: 50l, membranes: 1. Machine dimensions X/Y/Z: approx. 350mm/560mm/750mm, weight: approx. 55kg. Documentation available. An on-site inspection is possible.

Kuchnia cateringowa

Rieber/blanc/haka/bizerba/rational SA/CS 300

Niemcy

2005

używany

na żądanie

INNO29911

A fully equipped bistro is available. Components: 1) Dish conveyor dishwasher. 2) Furniture. 3) Small and large kitchen equipment. 4) Customer furnishings such as tables, chairs, and self-service counters. 5) Refrigerators. 6) Deep fryers and grills. 7) Cash registers and scales. 8) Dishes, plates, etc. 9) Extraction and filtration technology. Documentation available. An on-site inspection is possible.

Dwustronna szlifierka do szkła i myjka

Scheppach/ Abb/ Kuka/ 2500 C4/0E

Niemcy

2012

używany

na żądanie

INNO29905

A glass processing plant with several production lines is available. 1) Cutting line with automatic breaking system 2) Cutting line with automatic breaking system 3) Glass scrap disposal line 4) Glass scrap disposal line 5) Double-sided glass grinding and washing machine Scheppach 2500 C4/0E with washing machine T 4516 133 6) Double-sided glass grinding and washing machine Scheppach 2500 C4/0E with washing machine T 4516 133 and portal drilling machine, max. glass dimensions: 2600x2200mm 7) Control system 8) Water supply system for washing machines with circulation water treatment, sludge dewatering, chemical supply, and additional components 9) Horizontal tempering furnace Tamglass ProE-2442-ABS-20 10) Domino D550+ 10 (55W and 10mm scanner). A large number of spare parts, complete spare robots, and numerous glass racks in various formats are also available for purchase. Complete documentation available. On-site inspection is possible.

Tokarka centralna

Meuser & Co. Gmbh M2L

Niemcy

nieznany

używany

na żądanie

INNO29903

A conventional center lathe is available. An on-site inspection is possible.

Giętarka do rur CNC

Pulzer CNC 25L

Niemcy

1999

używany

na żądanie

INNO29902

Tube diameter: 25mm, wall thickness: 2mm, bending angle: 190°, feed length: 2000mm, weight: 2t, left-bending. Accessories: CNC IsoBend 2.0. Without mandrel bending device, monitor glass has impact damage but is still functional. An on-site inspection is possible.

Podnośnik-przechylacz

Lm Industry Srl KASTENKIPPER 180°

Niemcy

2020

używany

na żądanie

INNO29901

Max. load capacity: 2t, tilting angle: 180°, voltage: 400V, connected load: 4.25kW, compressed air connection: 6bar, CE marking: available. Tilting mechanism: chain-driven with large drive sprocket, hydraulically assisted for safe and controlled tilting process, designed for complete turning of containers (180°). Receiving container: yellow container, specially secured with retaining brackets and locks. Operation: electrically controlled with safety interlock. With documentation. An on-site inspection is possible.

Frezarka CNC

Lasercomb ProPertinax

Niemcy

2009

używany

na żądanie

INNO29895

A Lasercomb CNC high-speed die milling machine is available. Travel X/Y: 1070mm/1070mm, number of spindles: 4, spindle speed: 50000rpm, continuous power: 180W. Dimensions X/Y: approx. 2100mm/1900mm, weight: approx. 430kg. Documentation available. An on-site inspection is possible.

Maszyna do druku kopert

Winkler + Dünnebier 202

Niemcy

1989

używany

na żądanie

INNO29894

Printing units outside/inside: 3/1, doctor blade units: available, envelope size range: booklet min./max.: 100mm/150mm–180mm/254mm, pocket min./max.: 89mm/120mm–187mm/305mm. Documentation available. An on-site inspection is possible.

Maszyna do druku kopert

Winkler + Dünnebier 202

Niemcy

1996

używany

na żądanie

INNO29893

Printing units outside/inside: 2/1, doctor blade units: 3, production capacity: 800 envelopes/min, window unit: Mini-Splice 356 CMG, roll/splicer: Winkler + Dünnebier 191, web guiding: BST EKR 1000, gumming: standard remoist (moisture-activated gumming for sealing flaps), ink pumps: 2, extraction: window punching waste. Documentation available. An on-site inspection is possible.

Maszyna do sortowania

Probat 48 FSA 2,5

Niemcy

2013

używany

na żądanie

INNO29885

A Probat coffee grading machine for sorting out defective coffee beans is available. Machine dimensions X/Y/Z: approx. 1200mm/1000mm/1800mm, weight: approx. 450kg. An on-site inspection is possible.

Belka podnosząca

Nordgreif/gks

Niemcy

1999

używany

na żądanie

INNO29882

Four lifting beams from the manufacturers Nordgreif and GKS are available. 1) Nordgreif, year of manufacture: 1999, load capacity: 8000kg, gripping width: 1000mm/3000mm, dead weight: approx. 280kg. 2) GKS, year of manufacture: 1994, load capacity: 6000kg, dead weight: approx. 220kg. 3) Nordgreif, year of manufacture: 1998, load capacity: 10000kg. 4) GKS, year of manufacture: 1994, load capacity: 6000kg. An on-site inspection is possible. Sale of individual units upon agreement.

Komórka robota

Wu/fanuc RZ-3/M20iA 35M

Niemcy

2017

używany

na żądanie

INNO29881

A robot automation cell WU Mechanische Werkstätte with a Fanuc robot for product handling for a lathe is available. Gripper system: double gripper, gripper manufacturer: Schunk, robot type: Fanuc M20iA 35M, robot axes: 6, max. payload: 35kg, robot reach: 1810mm, machine dimensions X/Y/Z: approx. 1700mm/1300mm/2200mm, weight: approx. 2000kg. Lathe power-on time: approx. 34000h, servo-on time (cell): 5700h, mechanical operating hours: 615h. This is only the automation. Documentation available. An on-site inspection is possible.