Maszyny Uzywane Niemcy - Innovac GmbH

Innovac GmbH Used machines from Germany

Przykład Centrum Obróbcze

Innovac maszyny-uzywane

Najnowsze oferty [481 - 500 of 2702]

Piekarnik wózkowy

Werner & Pfleiderer Green Line REC Green II

Niemcy

2023

używany

na żądanie

INNO30532

A recirculating rack oven WP is available. Tray dimensions X/Y: 600mm/800mm, max. rack trolley diagonal: 1070mm, max. rack trolley height: 1800mm, baking area: 10m², max. tray load: 350kg. Machine dimensions X/Y/Z: approx. 1550mm/1650mm/2550mm, weight: approx. 2000kg, controls: Navigo 3. Documentation available. An on-site inspection is possible.

Piekarnik pokładowy

Werner & Pfleiderer Matador MD 125 C 52

Niemcy

2003

używany

na żądanie

INNO30531

Baking area: 12m², decks: 5, deck dimensions X/Y: 1200mm/2000mm, loading guideline with 1kg bread: 30x5, heating type: oil, heating capacity: 90kW, version: Combitherm. Machine dimensions X/Y/Z: approx. 1900mm/3100mm/2450mm, weight: approx. 3000kg. Including lifting table. Documentation available. On-site inspection is possible.

Piekarnik pokładowy

Miwe Ideal 4000/4

Niemcy

1993

używany

na żądanie

INNO30530

A Miwe deck oven is available. Decks: 4, heating type: oil, heating circuits: 2, usable baking area: approx. 8m², oven width: 1200mm, oven depth: 1600mm, max. temperature: 300°C, machine dimensions X/Y/Z: approx. 1600mm/3350mm/2350mm, weight: approx. 2000kg. Including lifting table Unimetall SH 101. An on-site inspection is possible.

Sprężarka

Atlas Copco/schneider/donaldson GA 18/DK 3000 N/Ultrasep plus 30

Niemcy

1994

używany

na żądanie

INNO30529

A small compressor system including separator and dryer is available. 1) Compressor Atlas Copco GA 18, year of manufacture: 1994, air volume flow: 36.4l/s, max. operating pressure: 10bar, motor power: 18.5kW, speed: 1500rpm. 2) Air dryer Schneider Druckluft GmbH DK 3000 N, max. inlet temperature: 50°C, max. operating pressure: 16bar, refrigerant: R134a, refrigerant charge: 700g, operating overpressure: 17bar. 3) Oil-water separator Donaldson Ultrasep Plus 30, max. residual oil content: 10mg/l, max. compressor capacity: 30m³/min, oil adsorption capacity: 25l, machine dimensions X/Y/Z: approx. 900mm/1000mm/400mm, weight: approx. 70kg. An on-site inspection is possible.

Centrum do cięcia strumieniem wody

Soitaab Thesis 2040

Niemcy

2014

używany

na żądanie

INNO30528

A complete Soitaab waterjet cutting system, which until the year 2023 was only a demonstration machine, is available. 1) Main system Soitaab Thesis 2040, year of manufacture: 2014, cutting dimensions X/Y/Z: 4000mm/2000mm/200mm, control system: Soitaab 905unoS, control system year of manufacture: 2023, overall system dimensions X/Y/Z: approx. 5400mm/3300mm/2100mm. 2) High pressure pump KMT Neo 50, year of manufacture: 2022, max. operating pressure: 4100bar, last service: 09/2025. 3) Abrasive unit KMT Feedline V, year of manufacture: 2015. Including a storage container Müller, container capacity: 1000kg. Documentation available. An on site inspection is possible.

Piła do listew przyszybowych

Striffler 2733

Niemcy

nieznany

używany

na żądanie

INNO30527

A small Striffler glazing bead saw is available. Cutting speed: 36m/s, working length: 2400mm, miter setting: 45°, max. cutting width: 75mm, max. cutting height: 50mm, saw blade dimensions X/Y: 250mm/220mm, weight: approx. 100kg. An on-site inspection is possible.

Frezarka uniwersalna narzędziowa

Wmw FUW 315/III

Niemcy

1981

używany

na żądanie

INNO30526

Travel X/Y/Z: 500mm/280mm/330mm, table dimensions X/Y: 710mm/400mm, max. table load: 150kg, speed: 1800rpm, tool holder: SK40, feed rate: 1250mm/min, milling head swivel: +/-90°. Machine dimensions X/Y/Z: approx. 1800mm/2200mm/1800mm, weight: approx. 1800kg. An on-site inspection is possible.

Centrum obróbcze CNC

Mazak VTC-800/30SR

Niemcy

2015

używany

na żądanie

INNO30524

A CNC vertical long-bed machining center Mazak is available. Travel X/Y/Z: 3000mm/800mm/720mm, B-axis: 110°, C-axis: 360°, table diameter: 600mm, long-bed table dimensions X/Y: 3500mm/820mm, max. table load: 2500kg, spindle interface: BT40, speed: 18000rpm, rapid traverse: 50m/min, tool stations: 48, coolant pressure: 70bar. Machine dimensions X/Y/Z: approx. 5250mm/3650mm/3200mm, weight: approx. 16100kg, control: Mazatrol Matrix 2, spindle hours: 18502h. Including rotary table Nikken CNC 601MA, high-pressure coolant, center partition wall, Renishaw probe, touch probe RMP 60Q, CAD/CAM software Topsolid 7.18 and postprocessor. Documentation available. An on-site inspection is possible.

Kształtowarka

Hahndorf REWK 86/14

Niemcy

2007

używany

na żądanie

INNO30522

A Hahndorf keyway slotting and broaching machine is available. Stroke range slotting: 60mm-300mm, max. slot width slotting: 34mm, max. slotting length: 300mm, max. slot width broaching: 14mm, max. broaching tool length: 640mm, max. cutting speed forward/return: 3m/3m/min, weight: approx. 300kg. Documentation available. On-site inspection is possible.

Współrzędnościowa maszyna pomiarowa CNC

Mitutoyo Crysta Apex C 7106

Niemcy

2012

używany

na żądanie

INNO30521

A Mitutoyo coordinate measuring machine overhauled in 2023 is available. Measuring dimensions X/Y/Z: 705mm/1005mm/605mm, max. workpiece height: 800mm, table dimensions X/Y: 880mm/1720mm, max. table load: 1000kg, resolution: 0.1µm, traverse speed: 520mm/s, measuring speed: 8mm/s. Machine dimensions X/Y/Z: approx. 1500mm/2000mm/2750mm, weight: approx. 2000kg, control: GEOPAK and CAT 1000 PS. Including various probe trees. Documentation available. On-site inspection is possible.

Drukarka 3D

Stratasys Objet 350

Niemcy

2017

używany

na żądanie

INNO30519

Resolution X/Y/Z: 600dpi/600dpi/1600dpi, max. build dimensions X/Y/Z: 342mm/342mm/200mm, max. materials per component: 82, min. layer thickness: 16µm. Machine dimensions X/Y/Z: approx. 1400mm/1300mm/1100mm, weight: approx. 450kg. Documentation available. On-site inspection is possible.

Podnośnik kubełkowy

Wiese P20 Z-Form

Niemcy

2016

używany

na żądanie

INNO30518

A Wiese pendulum bucket elevator in Z-shape for gentle vertical and horizontal conveying of sensitive, light bulk materials (potato chips) is available. Particle size range: 50mm-60mm, max. conveying material temperature: 30°C, moisture: dry, bulk density: 0.07t/m³, conveying capacity: approx. 14.3m³/h, belt speed: 0.22m/s, max. bucket filling: 60%, belt material: EPDM, bucket width: 476mm, support roller diameter: 95mm. Lower edge discharge: 4960mm, feed vertical shaft center: 3490mm, vertical shaft center last discharge: 1675mm. Documentation available. An on-site inspection is possible.

Źródło lasera

Ipg Laser YLS-3000-CT

Niemcy

2013

używany

na żądanie

INNO30517

An IPG laser source with peripheral equipment is available. 1) IPG Laser YLS-3000-CT, year of manufacture: 2013, wavelength: 1070nm, modulation: 0kHz-5kHz, power control range: 10%-100%, power stability: +/-1%. Machine dimensions X/Y/Z: approx. 800mm/800mm/560mm, weight: approx. 400kg. 2) Industrial chiller IPG Laser LC 170.01-A.3.5, year of manufacture: 2013, cooling capacity: 17kW, max. operating pressure: 28bar, refrigerant: R407C, refrigerant quantity: 3.5kg. 3) Wire feeder Dinse DIX WD 300, feed rate: 20m/min, wire diameter range: 0.8mm-1.6mm, machine dimensions X/Y/Z: approx. 300mm/250mm/250mm. 4) Laser process head. Documentation available. On-site inspection is possible.

Maszyna do uszczelniania

Bettermach/dw-machinery LGYF-2200/DW-4200

Niemcy

nieznany

używany

na żądanie

INNO30516

Two induction sealing machines are available. 1) Shandong Better Onward Machinery LGYF-2200, foil material: aluminum, container material: nonmetallic bottles, sealing diameter range: 20mm-150mm, bottle height range: 20mm-600mm, sealing capacity: 120-300bottles/min, machine dimensions X/Y/Z: approx. 750mm/650mm/1600mm, weight: approx. 50kg. 2) Guangzhou Dingwei Machinery DW-4200, sealing diameter range: 15mm-130mm, bottle height range: 50mm-350mm, machine dimensions X/Y/Z: approx. 700mm/750mm/1400mm, weight: approx. 40kg. Documentation available. On-site inspection is possible. The images are samples.

Maszyna napełniająca

Breitner IDK 2085

Niemcy

1995

używany

na żądanie

INNO30515

An 8-station rotary filling machine Breitner including accessories is available. The machine was used for filling mustard jars. Glass volume: 250ml, filling capacity: 6000pieces/h, filling stations: 8. Format adjustment possible if required. Documentation available. On-site inspection is possible.

Tokarka uniwersalna CNC

Dmg Mori CTX beta 800 TC

Niemcy

2022

używany

na żądanie

INNO30513

A CNC double-spindle turning machine DMG Mori is available. Turning length: 800mm, power: 25kW/32kW, torque: 280Nm/360Nm, speed: 5000rpm, Y-axis: +/-100mm, B-axis: +/-110°, tool stations: 80, max. chuck diameter: 210mm, tool interface: HSK-A63, drawtube inner diameter: 67mm, control: Siemens 840D sl, operating hours: approx. 4786h, program hours: approx. 1937h. Including short bar loader IRCO ILS-MUK 100/16, oil mist separator and scraper chip conveyor. Documentation available. On-site inspection is possible.

Maszyna do erodowania drutu

Mitsubishi DWC 200H

Niemcy

1987

używany

na żądanie

INNO30512

A Mitsubishi wire EDM machine including an automatic wire changer (AWF system) is available. Travel X/Y: 381mm/749mm, table dimensions X/Y: 647mm/797mm, max. workpiece dimensions X/Y/Z: 647mm/749mm/259mm, max. workpiece weight: 950kg. Machine dimensions X/Y/Z: approx. 1850mm/2600mm/1950mm, weight: approx. 4100kg. Including 12 wire spools and one ceramic replacement plate. The wire changer is defective. Documentation available. An on-site inspection is possible.

Maszyna do formowania wtryskowego

Arburg/demag/stübbe D100/D150/320M

Niemcy

1993

używany

na żądanie

INNO30511

Some older plastic injection molding machines from Arburg, Demag and Stübbe are available. 1) Stübbe S110/345, year of manufacture: 1976, clamping force: 1000kN, shot weight: 140g, mold installation height min./max.: 180mm/480mm, opening stroke: 320mm, tie bar spacing: 360mm/355mm, screw diameter: 40mm, core pulls: 1. 2) Demag D 150-452 NC III, year of manufacture: 1990, clamping force: 1500kN, shot weight: 207g, mold installation height min./max.: 320mm/550mm, opening stroke: 430mm, tie bar spacing: 460mm/460mm, screw diameter: 45mm, core pulls: 1. 3) Demag D 100-275 NC II P, year of manufacture: 1989, clamping force: 1000kN, shot weight: 130g, mold installation height min./max.: 200mm/400mm, opening stroke: 350mm, tie bar spacing: 400mm/400mm, screw diameter: 38mm, core pulls: 1. 4) Arburg Allrounder 270M 250-75, year of manufacture: 1990, clamping force: 250kN, shot weight: 25g, mold installation height min./max.: 225mm/not specified, opening stroke: 325mm, tie bar spacing: 270mm/270mm, screw diameter: 20mm, core pulls: 1. 5) Arburg 320 850-210, year of manufacture: 1986, clamping force: 850kN, shot weight: 108g, mold installation height min./max.: 250mm/625mm, opening stroke: 375mm, tie bar spacing: 320mm/320mm, screw diameter: 35mm, core pulls: 0. On-site inspection is possible. Individual sale possible.

Piec do lutowania reflow

Mechatronika MR 260

Niemcy

2020

używany

na żądanie

INNO30509

A Mechatronika reflow soldering oven with automatic conveyor with stainless steel mesh is available. Conveyor width: 260mm, max. PCB component height: 25mm, heating length: 900mm, max. temperature: 280°C, conveyor speed: 180mm/min. Machine dimensions X/Y/Z: approx. 1650mm/600mm/400mm, weight: approx. 80kg. Documentation available. On-site inspection is possible. Image is an example.

Frezarka uniwersalna

Panak FV-2

Niemcy

nieznany

używany

na żądanie

INNO30508

Travel X/Y/Z: 800mm/400mm/440mm, table dimensions X/Y: 1285mm/355mm, quill stroke: 130mm, weight: approx. 2100kg. An on-site inspection is possible.