Używane maszyny z Niemiec - Strona 5

Tokarka uniwersalna

Maschstroj C11MB

Niemcy

1980

używany

na żądanie

INNO32654

Equipment: tailstock with handwheel, compound slide, cross slide, longitudinal carriage with apron, machine light, integrated machine stand, tool holder. Inspection possible by appointment.

więcej

Śrutownik sześciowalcowy

Seeger SSM. NR. 6

Niemcy

1969

używany

na żądanie

INNO32653

Capacity: 1800kg/h, speed: 300rpm, weight: 3300kg. Inspection possible by arrangement.

więcej

Współrzędnościowa maszyna pomiarowa CNC

Dea Global Performance

Niemcy

2010

używany

na żądanie

INNO32652

X-axis travel: 500mm, Y-axis travel: 700mm, Z-axis travel: 500mm, accuracy: 2.6µm + L/165mm, probing system: LEITZ HP-S-X1S, probe head: TESA articulating probe head, new part, probe head controller, new part, software: PC-DMIS CAD++ 2014, last calibration: 03/2026, no visible defects, calibrated regularly over several years, an on-site inspection is possible.

więcej

Sprężarka śrubowa do czynników chłodniczych

Bitzer CSW8573-90Y-40P

Niemcy

2015

używany

na żądanie

INNO32651

Offered is a screw compressor for industrial refrigeration systems. Swept volume: 410m³/h at 50Hz / 495m³/h at 60Hz. Speed: 2900rpm at 50Hz / 3500rpm at 60Hz. Maximum allowable pressure on the low-pressure side: 19bar. Maximum allowable pressure on the high-pressure side: 28bar. Degree of protection: IP54. Refrigerant of the original system: R134a. Condition: defective, water ingress following a pressure drop, repairable. Inspection possible by appointment.

więcej

Maszyna do gwintowania wewnętrznego

Hüller Ultromat UG 3

Niemcy

nieznany

używany

na żądanie

INNO32650

Offered: Mechanical tapping machine with change-gear feed. Equipped with T-slot worktable, tool holder, mechanical operating levers, foot switch and emergency stop button. Inspection possible by appointment.

więcej

Spawarka MIG/MAG

Cloos Qineo Tronic 450

Niemcy

2017

używany

na żądanie

INNO32649

6x Cloos Qineo Tronic 450 MIG/MAG welding machines, 1x Cloos GLC 451-C welding machine and 1x Cloos GLC 553/MC3 welding machine are available, 1) 6x Cloos Qineo Tronic 450 MIG/MAG welding machines, welding current: 40-450A, welding current at 60% duty cycle: 450A/36.5V, welding current at 100% duty cycle: 350A/31.5V, open-circuit voltage: 77-98V, mains voltage: 380-480V/50Hz/3-phase, power cable: 4x6mm², mains fuse protection: 400V/32A, protection rating: IP23, insulation class: F, cooling method: F, dimensions (without wire feeder): 1011x517x703mm, weight (without wire feeder): 88kg, year of manufacture: 5x2017, 1x2016, 2) 1x Cloos GLC 451-C welding machine, year of manufacture: 2003, 3) 1x Cloos GLC 553/MC3 welding machine, year of manufacture: 2008, additionally, 21 welding torches with long torch necks, 12x500mm, 4x600mm, 5x1500mm, and 53 FKS400 Autogen Ritter welding torch hose assemblies are included, an on-site inspection is possible.

więcej

Podciśnieniowy podnośnik tubowy

J. Schmalz Jumbo Ergo 85-350

Niemcy

2002

używany

na żądanie

INNO32648

Offered is a vacuum tube lifter with pillar-mounted jib crane. Maximum load capacity: 85kg. Weight of the lifting unit: 63.5kg. Equipped with a vacuum lifting unit, ergonomic control unit with handle, vacuum gripper, vacuum supply hose, side channel blower with filter, as well as a pillar-mounted jib crane with jib arm and movable suspension. Inspection possible by arrangement.

więcej

Wirówkowa suszarka do palet

Kitzinger Maschinenbau Gmbh conrion

Niemcy

2018

używany

na żądanie

INNO32647

Offered is a pallet spin drying system with infeed roller conveyor. Equipped with a stainless steel roller conveyor, enclosed machine housing, safety guard, control panel with emergency stop button, signal light and pneumatic components. Inspection possible by arrangement.

więcej

Tokarka centralna

Krasny Proletarij 16K20

Niemcy

1977

używany

na żądanie

INNO32646

Offered is a conventional center lathe with lead screw and feed rod. Thread cutting: metric and imperial threads. Speed and feed selection: mechanically via gearbox. Workpiece clamping: three-jaw chuck. Tool holder: four-way tool post. Equipped with longitudinal and cross slides, tailstock with quill, lead screw and feed rod, digital position readout and work light. Inspection possible by arrangement.

więcej

Piła formatowa

Niemcy

nieznany

używany

na żądanie

INNO32645

Offered is a sliding table saw with an aluminum sliding table. Cutting guide: Sliding table for rip cuts and crosscuts. Work surface: Machine table with additional table width extension. Equipped with an aluminum sliding table, adjustable rip fence, crosscut fence with flip stop, large support arm, saw blade guard with dust extraction port and dust extraction hoses. Inspection possible by arrangement.

więcej

Tokarka czołowa

Veb Werkzeugmaschinenfabrik 7. Oktober DP 2/S 3

Niemcy

nieznany

używany

na żądanie

INNO32644

Offered is a facing lathe with a large faceplate. Swing diameter over foundation plates: 2480mm. Center height above foundation plates: 1250mm. Faceplate diameter: 1600mm. Maximum faceplate torque: 14000Nm. Main spindle bore: 100mm. Front main spindle bearing diameter: 240mm. Turning tool shank cross-section: 50 × 50mm. Equipped with four chuck jaws, movable bed-mounted carriage, cross slide, tool holder, mechanical control levers and handwheels.

więcej

Tokarka karuzelowa

Sedin 1516

Niemcy

nieznany

używany

na żądanie

INNO32643

Offered is a single-column vertical turret lathe with tool turret. Equipped with a large rotary table with radial clamping slots, clamping brackets, vertical tool slide with turret head, digital position readout, work light and separate control panel. Inspection possible by arrangement.

więcej

Tokarka centralna

Tos Celákovice SU-63A

Niemcy

nieznany

używany

na żądanie

INNO32642

Offered is a conventional shaft lathe with tailstock. Swing over bed: 630mm. Swing over cross slide: 360mm. Center height above bed: 286mm. Spindle bore: 60mm. Spindle diameter at front bearing: 140mm. Number of spindle speeds: 30. Number of longitudinal feed steps: 41. Number of cross feed steps: 41. Longitudinal feed: 0.064-6mm/rev. Cross feed: 0.025-2.32mm/rev. Maximum workpiece weight according to manufacturer: 6000kg. Metric thread pitches: 0.219-48mm. Equipped with a large chuck, tailstock, four-way tool post, longitudinal and cross slides, as well as mechanical control levers and handwheels. Inspection possible by arrangement.

więcej

Wytaczarka pozioma

Union

Niemcy

nieznany

używany

na żądanie

INNO32641

Offered is a horizontal boring machine. Equipped with a rotary clamping table with T-slots, horizontal boring and milling spindle head, large vertical faceplate with clamping slots, mechanical control levers and handwheels, as well as an additional clamping surface with T-slots. Inspection possible by arrangement.

więcej

Frezarka konsolowa CNC

Wmw Heckert F 400/2

Niemcy

nieznany

używany

na żądanie

INNO32640

Offered is a CNC knee-type milling machine, model FU 400 × 1600. Clamping surface: milling table with T-slots. CNC control: VEB Numerik CNC-H 646. Equipped with a machine vise, flexible coolant hose and swiveling CNC control panel. Inspection possible by arrangement.

więcej

Tokarka tarczowa

Maschinenfabrik Ravensburg Ag P 30

Niemcy

nieznany

używany

na żądanie

INNO32639

Offered 250mm. Feed steps: 12. Cross-bed feed: 0.05-3mm/rev. Carriage and rotating section feed: 0.04-2.5mm/rev. Feed motor speed: 1000rpm. Feed motor power: 2.2kW. Permissible workpiece weight, cantilevered with a center of gravity distance of 300mm: approx. 5000kg. Permissible workpiece weight between centers, without additional support: 20000kg. Equipped with a large faceplate with clamping devices, cross-bed support, movable tool slide and mechanical lever controls. Inspection possible by arrangement.

więcej

Wiertarka promieniowa

Csepel RFh 75/1500

Niemcy

nieznany

używany

na żądanie

INNO32638

Offered is a radial drilling machine. Equipped with a height-adjustable radial arm, horizontally movable drill head, clamping table with T-slots and base plate with clamping slots. Inspection possible by arrangement.

więcej

Wiertarka promieniowa

Mas Kovosvit VOM 50

Niemcy

nieznany

używany

na żądanie

INNO32637

Offered is a radial drilling machine with a movable machine column. Equipped with a height-adjustable radial arm, electrically driven drill head, control panel with emergency stop button and machine base with guide rails. Inspection possible by arrangement.

więcej

Wiertarka promieniowa

Veb Maschinenfabrik John Schehr BR 40/2 × 1250

Niemcy

1989

używany

na żądanie

INNO32636

Offered is a radial drilling machine with infinitely variable spindle speed control. Spindle speed: 20-1200rpm. Spindle feed: 0.063-0.63mm/rev. Spindle travel: 355mm. Spindle taper: MT5. Distance from spindle to base plate: 280-1380mm. Clamping surface of the base plate X/Y: 1450mm/920mm. T-slots: 3, width 22mm, spacing 250mm. Arm rotation range: 360°. Equipped with a machine vise and coolant hose. Inspection possible by arrangement.

więcej

Hydrauliczna giętarka do blach

Knuth AHK 40200

Niemcy

nieznany

używany

na żądanie

INNO32634

Offered for sale is a hydraulic press brake for sheet metal processing. Pressing force: 200000kg. Bending length: 4050mm. Distance between uprights: 3100mm. Stroke: 190mm. Throat depth: 260mm. Rapid approach speed: 100mm/s. Working speed: 7mm/s. Return speed: 77mm/s. Equipped with a side-mounted control panel, front workpiece supports and side safety guards. Weight: approx. 15000kg. Overall dimensions X/Y/Z: approx. 5045mm/2420mm/2850mm. Inspection possible by arrangement.

więcej