Maszyny Uzywane Niemcy - Innovac GmbH

Innovac GmbH Used machines from Germany

Przykład Centrum Obróbcze

Innovac maszyny-uzywane

Najnowsze oferty [361 - 380 of 2563]

Szlifierka powierzchniowa

Majevica BRB 75.30.2KA

Niemcy

nieznany

używany

na żądanie

INNO29827

Longitudinal movement of the table manual drive: 750mm, longitudinal movement of the table hydraulic drive: 730mm, transverse movement of the table manual drive: 300mm, transverse movement of the table hydraulic drive: 290mm, usable surface of the table: 700x250mm, number of T-slots: 3, width of T-slots: 14mm, vertical movement of the grinding head: 400mm, division value of the grinding head manual drive: 0.01mm, distance between the inside of the grinding wheel and the column: 347.5mm, clearance under the new grinding wheel: 355mm, maximum grinding wheel diameter: 305mm, minimum grinding wheel diameter: 230mm, grinding wheel width: 25mm, grinding wheel bore: 127mm, division value of the cross table manual drive: 0.02mm, longitudinal feed of the table hydraulically: 2-25m/min, cross feed of the table stepwise, hydraulic and adjustable: 2-16mm/stroke, cross feed of the support hydraulically and continuous: 0.5-6m/min, volume of the hydraulic unit: 35l, cooling device for grinding wheel/on demand: 30l. No defects known, with documentation, an on-site inspection is possible.

Maszyna do lutowania na fali

Seho 8040 PCS

Niemcy

1997

używany

na żądanie

INNO29826

Seho 8040 PCS with laminar and turbulent wave, preheating with heating plates and IR radiator, minimum quantity flux system, component cooler at the outlet, wave width: 400mm, max. usable working width: 390mm, max. component height: 100mm, max. PCB length: 562mm, solder nozzle: Delta B, max. wave height: 8mm, solder volume: 400kg, heating capacity solder pot: 9kW, heating-up time 20-250°C: approx. 150min, heating-up time 190-250°C: approx. 60min, preheating zone length: 700mm, three heating zones: 3x 3kW, max. preheating capacity: 9kW, transport angle: manually adjustable, 6-8°, transport speed: 0.5-2m/min, running direction: from left to right, with loading aid/slide conveyor (1000mm), unloading aid (500mm) and entry stopper for solder frame separation, exhaust connection diameter: 2x 150mm, extraction capacity per connection: 500m³/h, supply voltage (50Hz): 230/400V, rated power: 31,000W, total connected load: 18.5kW, compressed air connection: R 1/4 inch (6 bar), nitrogen connection: R 1/4 inch (6 bar). With microprocessor control PCS 96, alphanumeric display & membrane keypad (16 lines of 40 characters), 100 soldering programs, interface for host computer with visualized machine overview & BDE data backup, interface for BDE data acquisition via serial printer, control loop for transport and heating. Length: 2300mm, width: 825mm, height: 1615mm, weight without solder filling: 400kg.

Centrum obróbcze CNC

Chiron FZ 08W MAGNUM high speed

Niemcy

2011

używany

na żądanie

INNO29825

X-axis: 300mm, Y-axis: 250mm, Z-axis: 250mm, rapid traverse (X/Y/Z): 40/40/60m/min, chip-to-chip time: 1.5s, clamping surface dimensions: 2x 550x300mm, max. spindle speed: 15,000/min, torque: 23Nm, tool holder: HSK-A32, number of tools: 12, tool changer: CHIRON basket changer, control: GE Fanuc Series oi-MC. An on-site inspection is possible.

Maszyna do zgrzewania sworzni

Soyer BMK-12W

Niemcy

2000

używany

na żądanie

INNO29822

Gun: PH-3N, voltage: 400V, weight: 50kg. Supplied with operating manual, 2x ground cables with clamp BMS/BMK, gas connection, HZ-stud holder, adapter piece and key. An on-site inspection is possible.

Elektrostatyczna instalacja do natryskiwania farb

Blo Delphin

Niemcy

2011

używany

na żądanie

INNO29821

The machine is in very good condition and ready for operation. An on-site inspection is possible.

Częściowy łańcuch

Liba

Niemcy

1991

używany

na żądanie

INNO29820

These are 21x21 inch and 30x42 inch warp beams, for direct warping and knitting mills. With documentation, without accessories. No defects known, last overhauled. An on-site inspection is possible.

Piekarnik uniwersalny

Memmert UF30

Niemcy

2020

używany

na żądanie

INNO29819

Operating temperature: 10-300°C, setting temperature: 20-300°C, setting accuracy: up to 99.9°C: 0.1°C, from 100°C: 0.5°C, temperature sensor: 1x Pt100 DIN class A, 4-wire measurement, control: Control COCKPIT Single DISPLAY, digital PID microprocessor controller with TFT color display, timer: 1 minute to 99 days, functions: SetpointWAIT, calibration of 3 temperature values, parameter selection (temperature, circulating air motor, exhaust air, program runtime, time zones), electronically controllable air turbine adjustable in 10% steps, fresh air via adjustable exhaust flap with preheating, exhaust port with throttle valve electronically controllable, logging: storage in case of power failure, programming: data logger evaluation via Ethernet, AtmoCONTROL software optional via USB, safety: electronic temperature monitoring, mechanical limiter TB, protection class 1 (DIN 12880), self-diagnosis system, internal dimensions: 400x320x250mm, volume: 32l, max. inserts: 3, max. load: 60kg, max. load per insert: 20kg, length: 650mm, width: 660mm, height: 890mm, weight: 45kg. The oven has hardly been used. An on-site inspection is possible.

Tokarka CNC

Gildemeister CTX 200E

Niemcy

1998

używany

na żądanie

INNO29818

Base machine CTX 200E with driven tools, C-axis and 1x back working. Includes DATAPILOT software package TurnPlus, cooling unit for control cabinet, hinge belt chip conveyor, discharge height: 1100mm including coolant tank, tool holder set for universal disc turret with tool holders for external machining, boring bar holders, tools with cylindrical shank holders, sealing plugs, reducing sleeves. Bar gripper, axial complete, workpiece pick-up device, tool spindles 3x axial for drilling/milling/tapping, 1x radial for drilling/milling/tapping, 1x for saw blades, collet chuck complete for main spindle, collet chuck complete for counter spindle, 17x DIN collets 173E round Ø 3-40mm, 2x DIN collets 173E, hex SW 7 and 12mm, 2x DIN collets 173E, square SW 8mm. Bar loading magazine IEMCA BOSS 542/32, guide channel set LW 13, additionally for IEMCA BOSS 542, 13x guide jaws for bar loading magazine IEMCA BOSS 542/32, Ø 8-41mm. With complete documentation. The machine has been idle for one year as the turret head is missing, no further defects known, operating hours unknown, without maintenance records. With bar loader and numerous tools.

Frezarka uniwersalna CNC

Deckel Maho DMU 50T

Niemcy

1998

używany

na żądanie

INNO26767

Spindle speed range: 9000rpm, travel X/Y/Z: 500mm/400mm/400mm, feed rate: 10000mm/min, rapid traverse: 12m/min. Table dimensions X/Y: 700mm/500mm, max. table load: 200kg, number of T-slots: 7, distance between T-slots: 63mm. Control: Heidenhain, tool changer: 16-fold, dimensions X/Y/Z: 4000mm/2200mm/2450mm, weight: approx. 3500kg.

Przekładnia czołowa

Sew-eurodrive SDGA-1105 SP

Niemcy

2021

używany

na żądanie

INNO29815

Lifting capacity: 52t, drive shaft diameter of the hollow shaft: 245mm, brake shaft dimensions: 100x190mm, drive shaft dimensions: 80x140mm, ambient temperature: -15 to 45°C, center distance: 1105mm, rated power: 275kW. The gear is still unused. An on-site inspection is possible.

Podwójna piła ukośna

Elumatec DG104

Niemcy

2006

używany

na żądanie

INNO29814

Smallest cutting length at 90°: 350mm, smallest cutting length at 45° inclined: 350mm, swiveling range inward: 90-45° (down to 22.5° manually with digital display), tilting range inward pneumatically: 90-45°, saw blade diameter: 420mm, saw blade speed: 2800/min, electrical connection: 230/400, power output per motor: 4kW, compressed air connection: 7bar, air consumption per working cycle: 40l without spraying, 64l with spraying, length: 4380mm, width: 2871mm, height: 1985mm. With complete documentation, without accessories. An on-site inspection is possible, but not under power. The machine is already dismantled and ready for loading. No defects known, was regularly maintained by the manufacturer.

Automatyczna maszyna do klejenia pudełek składanych

Eterna EFOLD 1100 ELITE

Niemcy

2020

używany

na żądanie

INNO29813

Features: belt feeder, Ero gluing system (cold glue, 4 nozzles), folding unit, pressing belt, max. sheet size: 60-800x126-1100mm, production possibilities: straight line, crash lock bottom, 4- and 6-corner, double-wall boxes and file covers/piches/envelopes, board thickness: 200-800g/m², corrugated board: N-, E-, F-flute, max. belt speed: 320m/min, shaking speed: 20m/min, main motor power: 11kW, total power requirement: 35kVA, max. air consumption: 0.7m³/min, length: 12,700mm, width: 2600mm, weight: 7t. Operational hours counter: 1494h. An on-site inspection is possible.

Płaska maszyna do wykrawania i tłoczenia

Heidelberger Druckmaschinen Promatrix 106 CS/CSB

Niemcy

2021

używany

na żądanie

INNO29812

Features: automatic non-stop delivery with conveyor, non-stop feeder with rods, pull mark left, push mark right, quick clamping frame for tooling, lower stripping station, upper stripping station, two exchange frames for lower stripping station. Without die-cutting plates. Processable materials: min. paper 90g/m², max. solid board 2000g/m², max. corrugated board/ with MasterSet 4/ 2mm, max. sheet size 760x1060mm, min. sheet size/with MasterSet 300x350/ 350x400mm, max. cutting pressure: 2.6MN/ 260t, max. machine speed: 8000 sheets/h, max. feeder pile height without non-stop/ in non-stop operation: 1500/ 1200mm, max. feeder pile weight: 1500kg, max. delivery pile height: 1400mm, max. delivery pile weight: 900/ 1340kg. Operating hours: 1525h. An on-site inspection is possible.

Maszyna do erozji iskrowej

Wagner Maschinen DM-323

Niemcy

1988

używany

na żądanie

INNO29811

Two DM-323 electrical discharge machines are available. Operating hours machine 1/2: 12,134.51 / 32,704.5 h. Operating manuals and circuit diagrams available. An on-site inspection is possible.

Silniki niskonapięciowe

Siemens SIMOTICS SD 1LE5/ 1LE1

Niemcy

2021

używany

na żądanie

INNO29810

A total of 12 low-voltage motors are available, 4x SIMOTICS SD 1LE5 and 8x SIMOTICS SD 1LE1. (1) SIMOTICS SD 1LE5, Motor type: Three-phase asynchronous motor, low voltage, cast iron housing, Severe Duty series SIMOTICS SD (model range 1LE5), protection class: standard IP55, insulation class: Class F, operating mode: continuous duty S1 according to IEC/DIN EN 60034-1, environment: -20°C to 40°C, up to 1000m above sea level. (2) SIMOTICS SD 1LE1, rated voltage: standard voltages, operating mode: continuous duty S1, housing: cast iron (Severe Duty), cooling: self-ventilated, insulation class: F (temperature class 155 / utilization B), speed range: 750-3600/min, max. rated torque: approx. 1703 Nm. The motors are still unused, the year of construction is 2021/22. An on-site inspection is possible.

Tokarka

Meuser M1 P

Niemcy

nieznany

używany

na żądanie

INNO29809

Speed: 45-1800/min, the machine is functional. An on-site inspection is possible.

Tokarka CNC

Gildemeister NEF 400

Niemcy

2006

używany

na żądanie

INNO29808

Max. spindle speed: 4000/min, connected load: 21kVA, control: Siemens Sinumerik 840D, length: 2100mm, width: 1750mm, height: 1710mm, weight: 2.8t. With chip conveyor, internal cooling and manually movable tailstock, without turret. The machine requires an overhaul. An on-site inspection is possible.

Uniwersalny system do wędzenia i gotowania

Bayha & Strackbein 1500C

Niemcy

1999

używany

na żądanie

INNO29804

Two identical smoking and cooking systems are available. Suitable for the production and refinement of sausages and meat products, poultry, fish, cheese and baked goods, hot smoking, warm smoking, cold smoking, moist smoking, intensive smoking, quick smoking, reddening, sweating, scalding, steaming, cooking, hot air cooking, semi-preservation, baking, roasting and defrosting. Heating capacity: 24kW, connected load: 31.5kW. With operating manual. An on-site inspection is possible.

Piła taśmowa

Meber SR700

Niemcy

2017

używany

na żądanie

INNO29803

Flywheel diameter: 700mm, worktable dimensions: 694x1010mm, cutting capacity: 430x680mm, flywheel width: 40mm, band speed: 2800/min, flywheel speed: 782/min, saw band length: 5040-5190mm, motor power: 4HP, connected load: 3kW, noise level: 82 dB(A), net weight: 375kg. An on-site inspection is possible.

Urządzenie odśrodkowe

Walther Trowal TT 90-A/2C-V9

Niemcy

2018

używany

na żądanie

INNO29802

Gross volume: 90l, max. usable volume: 60l, max. filling weight: 175kg, drive type of the table: frequency-controlled electric gear motor, connected load table drive: 4kW, nominal speed table: 213/min, tilting drive type: hydraulic cylinder, tilting angle: 49°, max. tilting height when emptying: 2200mm, loader tilting drive type: hydraulic cylinder, tilting angle: 41°, max. tilting height when emptying: 2700mm, buffer drive type: electric unbalanced motor, drive power: 0.3kW, tilting drive type: hydraulic cylinder, tilting range: -25° to 12°, screening machine drive type: 2x electric unbalanced motor, drive power: 2x 0.25kW, media return chute drive type: electric unbalanced motor, drive power: 0.19kW, delivery rate hydraulic unit: 8.0l/min, operating pressure: 170bar, drive power pump motor: 3kW, tank volume: 30l, valve voltage: G24, length: 2812mm, width: 2094mm, operating hours: 14,021h, motor running hours: 427h. Application areas: edge rounding, coarse and fine grinding, descaling, degreasing, shining, polishing, deburring, cleaning. With documentation, an on-site inspection is possible.