Używane maszyny z Niemiec - Strona 18

Pionowe centrum obróbcze CNC

Willemin-macodel W 408S

Niemcy

2008

używany

na żądanie

INNO32342

Two Willemin-Macodel W 408 and four Willemin-Macodel W 408S are available, year of manufacture W 408: 1997, 2002, year of manufacture W 408S: 2005, 2006, 2007, 2008, an on-site inspection is possible.

więcej

Tokarka centralna

Heidenreich & Harbeck M 530

Niemcy

1967

używany

na żądanie

INNO32341

Swing over bed: 540mm, swing over carriage: 280mm, max. cross slide travel: approx. 410mm, max. compound slide travel: approx. 140mm, tailstock quill travel: 225mm, main spindle speed steps: 24, spindle speed: 9-1400rpm, 32 longitudinal feeds: 0.063-2.24mm/rev, 32 cross feeds: 0.032-1.12mm/rev, metric thread pitch: 0.25-560mm, module threads: module 0.1-50, diametral pitch threads: pitch 160-0.5, center height above flat guideway: 265mm, center height above top of V-way: 247mm, bed width: 403mm, main spindle with spindle nose according to DIN 55022: size 11, spindle bore: 103mm, internal taper: 1:20, largest diameter: 109mm, Morse taper of centers: No. 5, leadscrew pitch, standard: 12mm, tailstock quill diameter: 80mm, standard drive power: 18.5kW, rated speed of drive flange motor: 1400rpm, turning tool cross-section according to DIN 770: 25x25mm, max. faceplate diameter: 500mm, max. three-jaw and four-jaw chuck diameter according to DIN 6350: 315mm, weight: 3t, with work light, coolant system with chip tray, four-way tool post with face serration for one-hand operation on the compound slide, operating manual and fixed steady rest. An on-site inspection is possible.

więcej

Tokarka

Knuth DL 3000

Niemcy

nieznany

używany

na żądanie

INNO32339

Max. swing over bed: 615mm, max. swing over cross slide: 345mm, distance between centers: 3000mm, spindle bore: 70mm, spindle taper: MT5, forward speed steps: 18, forward speed range: 14-750rpm, reverse speed steps: 9, reverse speed range: 21-857rpm, standard longitudinal feed: 32 steps, 0.1-1.42mm/rev, standard cross feed: 32 steps, 0.03-0.46mm/rev, fine longitudinal feed: 8 steps, 0.048-0.089mm/rev, fine cross feed: 8 steps, 0.015-0.028mm/rev, coarse longitudinal feed: 32 steps, 1.52-2.28mm/rev, coarse cross feed: 32 steps, 0.48-7.2mm/rev, rapid traverse longitudinal: 6m/min, rapid traverse cross: 2m/min, metric threads: 54, range: 1-240mm, Whitworth threads: 37, range: 1-28threads/inch, compound slide travel: 230mm, cross slide travel: 400mm, distance from spindle center to tool holder: 32mm, tool dimensions: 30x30mm, tailstock quill diameter: 100mm, tailstock taper: MT5, quill travel: 205mm, bed width: 490mm, main motor power: 11kW at 1450rpm, rapid traverse motor power: 0.12kW at 1450rpm, coolant motor power: 0.09kW, coolant delivery rate: 25l/min, length: 5500mm, width: 1500mm, height: 1300mm, weight: 4.7t, with documentation. An on-site inspection is possible.

więcej

Grubościówka

Scm Minimax S 41es TERSA

Niemcy

2021

używany

na żądanie

INNO32337

Planing width: 410mm, working height: 3mm-240mm, max. stock removal: 5mm, feed speed: 12m/min, thicknessing table X/Y: 775mm/423mm, extraction port diameter: 120mm, operating hours: approx. 350h, weight: approx. 361kg. Equipped with 4-knife TERSA cutterblock for quick knife changes without adjustment or screws, solid gray cast iron thicknessing table with 4-column guide on four large spindles, integrated lifting device for a stable table position without additional locking, manual thicknessing table adjustment with numerical readout and reading accuracy of 1/10mm, helical-toothed steel infeed roller for gentle stock removal from 0.2mm and satin-finished steel outfeed roller. The machine is currently in storage.

więcej

Silnik elektryczny

Siemens/adda 1LA51860BB60-Z/1LA51861BD60-Z/DM1 200L6/4L

Niemcy

nieznany

używany

na żądanie

INNO32336

Three Siemens/Adda electric motors are offered. 1) Siemens 1LA51860BB60-Z, power: 5/18.5kW, weight: 145kg. 2) Siemens 1LA51861BD60-Z, power: 6.5/19kW. 3) Adda DM1 200L6/4L, power: 9/26kW, weight: 248kg. The motors are reconditioned or new. An on-site inspection is possible.

więcej

Magazyn do podajnika barów

Top Automazioni XFS380SX

Niemcy

2020

używany

na żądanie

INNO32335

Bar length: 3000mm, max. bar diameter: 80mm, operating cycle: fully automatic, monitoring and fault diagnostics: via display, part length: presettable, feed control: AC servo motor, bar diameter: adjustable via PLC keypad in 1mm increments, remnant extraction: to the rear or ejection to the front, guide channels: Vulkollan plastic, usable magazine width: approx. 900mm, control: integrated PLC, weight: approx. 2500kg. Documentation available. An on-site inspection is possible.

więcej

Maszyna etykietująca

Gernep Soluta 6-720 2SK SD

Niemcy

2023

używany

na żądanie

INNO32334

Offered for sale is a self-adhesive labeling machine. Nominal output: 11000bottles/h, reference circle diameter: 720mm, control range: 2000 to 12000bottles/h, number of container plates: 12, pitch: 188.4mm, starwheel diameter: 480mm, starwheel pitch: 8, number of self-adhesive labeling stations: 2, direction of operation: left-hand machine, control: touch panel. Equipped with infeed screw 1x, infeed/outfeed starwheel 1x, bottle plates 1 set, centering hoods 1 set, swivel arm, free-standing control cabinet. Inspection possible by appointment.

więcej

Tokarka CNC

Boehringer VDF 315C

Niemcy

1991

używany

na żądanie

INNO32333

Offered for sale is a robust universal CNC lathe. Turning length: 3000mm, max. torque: 2240Nm, spindle speed range: 16-2500rpm, feed rate: 0.001-9999.999mm/min, rapid traverse rate: 10000mm/min, feed force: 15kN, tailstock quill force: max. 15kN, control: FANUC 15 TF. Equipped with hydraulic tailstock, drum turret, steady rest (range 72-220mm and 28-120mm), various spare parts, defects: machine bed worn, X-axis bearing arrangement makes noise. Weight: approx. 8500kg, overall dimensions X/Y/Z: approx. 6500mm/2200mm/2000mm. Inspection possible by appointment.

więcej

Maszyna do dalszego przetwarzania

Cartes Série GEMINI GE362VR

Niemcy

2016

używany

na żądanie

INNO32332

Equipment: 1) Cartes GE362VR finishing machine, infeed unit: servo-driven pneumatic 76mm clamping mandrel/expansion shaft, accommodates rolls up to 800mm in diameter or 150kg, automatic electronic web tension and roll diameter control with photocell, automatic stop function at end of material, electronic web guide with ultrasonic sensor for precise web control, splicing table with pneumatic clamps, adhesive tape dispenser, photocell for detecting print marks and any contrast points on pre-printed material, complete servo motor control of the material web, Vetaphone corona treatment system, flexo coating unit, fully rotary operation, equipped with laminating module, rotary flexo coating unit, UV dryer, specification in the source document: 24W/cm / 160W/cm, for laminating, printing or full-surface overcoating/coating, 2) Semi-rotary die-cutting unit with Image Distortion System (IDS) and Air Gap System (AGS): die-cutting system, magnetic cylinder, air-gap adjustment system, semi-rotary and fully rotary gearless die-cutting system, printing plate/die plate thickness range: 0.2-2mm, Image Distortion System (IDS), 3) Air Gap System (AGS), 4) outfeed unit, web control, complete servo motor control of the material web, slitting unit, 10 pivoting razor blades with lateral adjustment, additionally 8 knife/counter-knife cutting groups for longitudinal slitting, rewinding shafts, first rewinding shaft, independent servo-driven pneumatic 76mm expansion shaft, for rolls up to 800mm or 150kg, automatic web tension control, direction of rotation: clockwise/counterclockwise, with documentation. An on-site inspection is possible.

więcej

Robot spawalniczy

Abb Automation IRB 1600 M2004

Niemcy

2006

używany

na żądanie

INNO32331

An industrial welding robot is offered. Reach: 1450mm, payload: 5kg, operating hours: 2213h, welding power source: ESAB AristoMig 500W, max. welding current: 500A, duty cycle: 60% at 500A/100% at 400A, controller type: IRC, robot variant: 1600-5/1.45, controller: IRC. Equipment: ESAB AristoMig 500W welding power source, IRC control cabinet, linear axes/positioner tracks. Weight: approx. 500kg, overall dimensions X/Y/Z: approx. 1200mm/800mm/1600mm. An inspection is possible by arrangement.

więcej

Maszyna do układania tkanin

Badets A & Fils Sarl DERTAN-B

Niemcy

2017

używany

na żądanie

INNO32330

Working width: 2500mm, an on-site inspection is possible, not under power.

więcej

Odciąg oparów spawalniczych

Kemper System 9000

Niemcy

2015

używany

na żądanie

INNO32329

A central welding fume extraction system is offered. Airflow: 30000m³/h, airflow: 30000m³/h, motor power: 30kW, compressed air connection: 6-8bar, max. static pressure: 2500Pa, duty cycle: 100%, control: PLC. The system is equipped with 2 spark traps and various ductwork components (extraction arms and hoods not included). An inspection is possible by arrangement.

więcej

Centrum obróbcze CNC

Brother TC-S2C

Niemcy

2007

używany

na żądanie

INNO32328

X-axis: 500mm, connected load: 30.8kVA, length: 1624mm, width: 1560mm, height: 2829mm, weight: 2.4t, operating hours: 8,840h, power-on time: 89,352h, total operating hours: 28,840h, an on-site inspection is possible.

więcej

Maszyna do sitodruku

Mhm SYNCHRO PRINT 3000

Niemcy

nieznany

używany

na żądanie

INNO32325

Two identical screen printing machines are available, max. frame dimensions: 750x1100mm, compressed air connection: 8bar, indexer connected load: 2.5kW, squeegee connected load: 0.6kW, an on-site inspection is possible.

więcej

Linia galwaniczna

C.hafner HF VARIO

Niemcy

nieznany

używany

na żądanie

INNO32324

A compact electroplating unit is offered. Electrolytic bath for gold and silver refining applications, control: microprocessor control. Equipped with an integrated control unit with display and keypad. Weight: approx. 15kg, overall dimensions X/Y/Z: approx. 450mm/300mm/350mm. Inspection by arrangement is possible.

więcej

Piła do cięcia paczek

Holtec HF 121

Niemcy

1990

używany

na żądanie

INNO32323

A mobile package crosscut saw for sawn timber is offered. Guide bar length: 1200mm, guide bar type: STIHL, chassis: manually movable, control: manual. Equipped with STIHL guide bar, robust chassis with pneumatic tyres, CEE plug with cable, protective guard. Weight: approx. 250kg, overall dimensions X/Y/Z: approx. 1500mm/800mm/2500mm. Inspection by arrangement is possible.

więcej

Forma do formowania wtryskowego

W23630, W23635, W61014F2, W61015F5, W61019, W62539

Niemcy

nieznany

używany

na żądanie

INNO32322

A package of six injection moulds for the series production of office organization products is available. The molds can be used to manufacture nestable filing trays, PET filing trays A4-C4, high-gloss and matte PS filing trays, a frame for a 3-tier filing tray unit, and a PET desk organizer. Materials processed: PET, recycled PET and PS. Mold numbers: W23630, W23635, W61014F2, W61015F5, W61019 and W62539. Mold dimensions depending on the mold: 397-570mm × 396-820mm × 369-637mm. Mold weights where documented: 450-1450kg. Average cycle times: 24.4-43.2s. Machine classes previously used where documented: 250t, 275t and 380t. According to the available documentation, the molds are in good condition. W61019 is used exclusively to manufacture the frame for the 3-tier filing tray unit. The molds are sold as a complete package. An on-site inspection of the molds is possible by arrangement.

więcej

Maszyna do formowania wtryskowego

Krauss Maffei Extra 100-430

Niemcy

2006

używany

na żądanie

INNO32321

Clamping force: 800kN, an on-site inspection is possible.

więcej

Maszyna pomiarowa współrzędnych 3D CNC

Werth ScopeCheck 300/S/Z 3D CNC

Niemcy

2021

używany

na żądanie

INNO32320

X-axis: 300mm, Y-axis: 200mm, Z-axis: 200mm, max. table load: 20kg, temperature gradient: 2K/h, relative humidity: 40-70%, length: 750mm, width: 737mm, height: 1664mm, weight: 260kg, operating hours: approx. 100h, with documentation, regularly serviced and inspected by the manufacturer. An on-site inspection is possible.

więcej

Maszyna wiążąca

Kettma Hamburg 100 KA

Niemcy

1968

używany

na żądanie

INNO32319

Four identical Kettma Hamburg 100 KA linking machines, one KMF 105 linking machine, Series 5, and spare parts are available, an on-site inspection is possible.

więcej