Used machines Germany - Innovac GmbH

Electric Forklift Truck

Linde E50/600HL

Germany

2020

used

on request

INNO29923

Mast: triplex, lift height: 6015mm, drive: electric, load capacity: 4990kg, load center: 600mm, weight: approx. 5800kg, battery weight: approx. 2200kg, operating hours: 1790h. Documentation available. An on-site inspection is possible.

more

Compact Filtration System

Lta AC 3002-R

Germany

2016

used

on request

INNO29922

Three filtration systems LTA AC 3002-R are available. Power: 1380VA, output voltage: 11kV, frequency: 50/60Hz, power connection: 2.6A, weight: 2x 130kg, 1x 135kg. An on-site inspection is possible, the systems have already been dismantled.

more

Combined Heat and Power Plant

Kw Energie smartblock 50

Germany

2016

used

on request

INNO29921

Fuel: natural gas (NG), engine: HMG, space heating unit with CHP: yes, condensing boiler: no, additional heating unit: no, low-temperature boiler: no, B11 boiler: no, combi unit: no. Rated heat input P: 88kW, annual efficiency of the space heating system η: 136%, energy efficiency class: A++, usable heat output at rated heat input with additional heater switched off/on: 87.9kW, thermal efficiency at rated heat input with additional heater switched off/on: 57.5%, electrical efficiency at the heat output of the space heating unit with CHP with additional heater switched off/on: 33.5%, auxiliary power consumption at full load/part load el: 1.132kW, in standby mode P SB: 0.06kW, standby heat loss P stby: 0.442kW, annual energy consumption Q HE: 1345kWh, sound power level indoors L WA: 72dB, operating hours: 42,892h. Water was detected in the oil circuit, the unit has an oil-related fault despite sufficient oil being present, and it also shuts down with the message 'engine too hot'. The control unit was overhauled by the manufacturer in 2024, and regular maintenance intervals for oil changes, spark plugs, valves, etc. have been carried out. With documentation.

more

Column Drilling Machine

Alzmetall AB 35 S

Germany

1978

used

on request

INNO29920

Drilling spindle stroke: 160mm, spindle taper: MK4, spindle speed: 1750rpm, reach: 300mm, feed: 0.3mm/rev, table dimensions X/Y: 620mm/470mm, machine dimensions X/Y/Z: approx. 620mm/950mm/1900mm, weight: approx. 450kg. Includes coolant system and threading device. An on-site inspection is possible.

more

Hardness Testing Machine

Mitutoyo Durotwin Plus 963

Germany

unknown

used

on request

INNO29919

Scales: Rockwell/Rockwell Superficial, max. workpiece height: approx. 180mm, max. test depth: approx. 165mm, dwell time: approx. 3s, data output: Digimatic/RS-232-C, machine dimensions X/Y/Z: approx. 250mm/520mm/780mm, weight: approx. 50kg. Documentation available. An on-site inspection is possible.

more

Air Cooler

Hydac OSCA 1L/10/1.3/M/A/1

Germany

unknown

used

on request

INNO29918

Two identical and unused Hydac air coolers in original packaging are available. Air volume flow: approx. 600m³/h, pump speed: 1000rpm, max. medium viscosity: approx. 2000mm²/s, medium: hydraulic oil/mineral oil, motor power: 0.25kW, pump flow rate: 10l/min, pump displacement: approx. 10cm³/rev, weight: approx. 30kg. Documentation available. An on-site inspection is possible.

more

Plate Shear

Darley GS.3016

Germany

1975

used

on request

INNO29917

Max. sheet thickness: 16mm, max. cutting length: 3000mm, weight: approx. 15t. The machine is in good condition. An on-site inspection is possible.

more

CNC Machining Center

Hurco VMX 24S

Germany

unknown

used

on request

INNO29916

A CNC 3-axis machining center is available. Travel X/Y/Z: 610mm/510mm/610mm, table dimensions X/Y: 760mm/610mm, max. table load: 700kg, tool positions: 24, tool holder: SK40, spindle speed: 10000rpm, rapid traverse: 24m/min. Machine dimensions X/Y/Z: approx. 2300mm/2400mm/2600mm, weight: approx. 4300kg, control: Ultimax 4. Includes coolant system, protective cabin, and a set of machine feet. Documentation available. An on-site inspection is possible.

more

Refrigerating plant

Climaveneta NECS/D/B/S 0302

Germany

2012

used

on request

INNO29915

A Climaveneta chiller is available. Cooling capacity: 73.8kW, power consumption: 27.6kW, compressors: 2, refrigeration circuits: 1, refrigerant: R410A, refrigerant charge: 10.2kg, heat recovery: cooling capacity 76.6kW/heating capacity 23.3kW. Machine dimensions X/Y/Z: approx. 2200mm/1150mm/1450mm, weight: approx. 680kg. Documentation available. An on-site inspection is possible.

more

Ventilation System

Wolf KG 40

Germany

unknown

used

on request

INNO29914

A Wolf ventilation system with supply and exhaust air units is available. 1) Supply air unit Wolf KG 40, air volume flow: 3000m³/h, pressure loss (external): 300Pa, heating capacity: 25.7kW, cooling capacity: 18.4kW, motor power: 3kW, motor speed: 2890rpm. 2) Exhaust air unit Wolf KG 40, air volume flow: 2000m³/h, pressure loss (external): 300Pa, motor power: 0.75kW, motor speed: 2855rpm. Documentation available. An on-site inspection is possible.

more

Reverse Osmosis Module

Bwt Permaq Compact 51

Germany

unknown

used

on request

INNO29913

A compact and mobile BWT reverse osmosis system including integrated tank is available. Throughput capacity: approx. 160l/h, recovery (WCF): 40%-75%, salt retention rate: over 98%, permeate conductivity: below 20µS/cm, tank volume: 50l, membranes: 1. Machine dimensions X/Y/Z: approx. 350mm/560mm/750mm, weight: approx. 55kg. Documentation available. An on-site inspection is possible.

more

Suction Unit

Wolf KG 40

Germany

unknown

used

on request

INNO29912

A Wolf exhaust unit for wet rooms is available. Air volume flow: 1000m³/h, pressure loss (external): 200Pa, motor power: 0.25kW, motor speed: 1500rpm. Documentation available. An on-site inspection is possible.

more

Catering Kitchen

Rieber/blanc/haka/bizerba/rational SA/CS 300

Germany

2005

used

on request

INNO29911

A fully equipped bistro is available. Components: 1) Dish conveyor dishwasher. 2) Furniture. 3) Small and large kitchen equipment. 4) Customer furnishings such as tables, chairs, and self-service counters. 5) Refrigerators. 6) Deep fryers and grills. 7) Cash registers and scales. 8) Dishes, plates, etc. 9) Extraction and filtration technology. Documentation available. An on-site inspection is possible.

more

Double-Sided Glass Grinding and Washing Machine

Scheppach/ Abb/ Kuka/ 2500 C4/0E

Germany

2012

used

on request

INNO29905

A glass processing plant with several production lines is available. 1) Cutting line with automatic breaking system 2) Cutting line with automatic breaking system 3) Glass scrap disposal line 4) Glass scrap disposal line 5) Double-sided glass grinding and washing machine Scheppach 2500 C4/0E with washing machine T 4516 133 6) Double-sided glass grinding and washing machine Scheppach 2500 C4/0E with washing machine T 4516 133 and portal drilling machine, max. glass dimensions: 2600x2200mm 7) Control system 8) Water supply system for washing machines with circulation water treatment, sludge dewatering, chemical supply, and additional components 9) Horizontal tempering furnace Tamglass ProE-2442-ABS-20 10) Domino D550+ 10 (55W and 10mm scanner). A large number of spare parts, complete spare robots, and numerous glass racks in various formats are also available for purchase. Complete documentation available. On-site inspection is possible.

more

Working Table

Bott Gmbh IGUS TC14 006 553

Germany

2016

used

on request

INNO29904

Twelve identical assembly tables are available. Length: 2020mm, width: 82mm, height: 240mm. No defects known, one of the tables has a newer worktop, without documentation. An on-site inspection is possible.

more

Center Lathe

Meuser & Co. Gmbh M2L

Germany

unknown

used

on request

INNO29903

A conventional center lathe is available. An on-site inspection is possible.

more

CNC Pipe Bending Machine

Pulzer CNC 25L

Germany

1999

used

on request

INNO29902

Tube diameter: 25mm, wall thickness: 2mm, bending angle: 190°, feed length: 2000mm, weight: 2t, left-bending. Accessories: CNC IsoBend 2.0. Without mandrel bending device, monitor glass has impact damage but is still functional. An on-site inspection is possible.

more

Lifting and Tilting machine

Lm Industry Srl KASTENKIPPER 180°

Germany

2020

used

on request

INNO29901

Max. load capacity: 2t, tilting angle: 180°, voltage: 400V, connected load: 4.25kW, compressed air connection: 6bar, CE marking: available. Tilting mechanism: chain-driven with large drive sprocket, hydraulically assisted for safe and controlled tilting process, designed for complete turning of containers (180°). Receiving container: yellow container, specially secured with retaining brackets and locks. Operation: electrically controlled with safety interlock. With documentation. An on-site inspection is possible.

more

Hydraulic Single-Column Press

Wmw Zeulenroda PYE 250 S/1M

Germany

unknown

used

on request

INNO29899

Nominal force: 2500kN, operating pressure: 20MPa, ram speed down/up: 210/110mm/s, ram stroke: 500mm, throat depth: 360mm, max. distance between table and ram: 800mm, rated current: 41A, control voltage: 60V, rated voltage: 380V, connected load: 20.5kW, weight: 8t. An on-site inspection is possible.

more

CNC Milling Machine

Mikron WF 31D

Germany

1992

used

on request

INNO29898

X-axis: 560mm, Y-axis: 500mm, Z-axis: 400mm, clamping table dimensions vertical: 300/450mm, number of threaded holes: 2/6, threaded hole spacing: 45mm, thread: M16, angle table clamping surface: 460/800mm, number of T-slots: 7, T-slot spacing: 63mm, T-slot width: 14mm, max. workpiece weight (recommended): 350kg. Milling spindle drive number of working spindle speeds: 21, speed (geometrically graduated): 40-4000/min, step increment: 1.259, spindle motor power: 3.3/4kW, tool holder: ISO 40 / M16 with draw-in groove, vertical quill stroke: 90mm, feed in all 3 axes steplessly adjustable: 2-3000mm/min, rapid traverse X-axis and Y-axis: 6000mm/min, rapid traverse Z-axis: 4000mm/min, feed motor torque longitudinal and transverse: each 3.5Nm, feed motor torque vertical: 7Nm, control: Heidenhain TNC 407, connected load: 8.7kW, length: 3705mm, width: 2430mm, height: 3100mm, weight of the machine with vertical milling head and angle table: 2410kg, weight of the crate base: 170kg, weight of the transport crate: 400kg, operating hours: 18,924h. Accessories: 3D probe, 20x tool holders, splash guard cabin, coolant pump, work light, handwheel, machine documentation. An on-site inspection is possible.

more