Used machines Germany - Innovac GmbH

Innovac GmbH Used machines from Germany

i.e. Machining Center MORI SEIKI

Innovac used-machines

Latest Offers [1 - 20 of 2716]

Wide Belt Sander

Sandingmaster SCSB2-1100

Germany

unknown

used

on request

INNO30946

A two-unit sanding machine Sandingmaster is available. Working width: 1100mm, max. workpiece width: 1000mm, max. workpiece height: 150mm, sanding belt dimensions X/Y: 1130mm/1900mm, feed: 14m/min. Machine dimensions X/Y/Z: approx. 3150mm/1500mm/1900mm, weight: approx. 2500kg. Including approximately 50 sanding belts with different crownings. Documentation available. An on-site inspection is possible.

Hot Press

Bürkle U 140

Germany

1984

used

on request

INNO30945

A Bürkle heated platen press with defective heating platen is available. Operating pressure: 348bar, nominal surface pressure: 30N/cm², max. surface pressure: 41N/cm², heating platen dimensions X/Y: 3500mm/1300mm. A cost estimate for the heating platen repair is available. Documentation available. An on site inspection is possible.

Panel Saw

Scheer PA 4137

Germany

unknown

used

on request

INNO30944

A panel dividing saw Scheer & Cie is available. Cutting length: 4200mm, fence depth: 4250mm, table length: 4200mm, max. cutting height: 70mm, height levels: 3, feed rate: 40m/min, return speed: 50m/min, angular pressure device: 2400mm, air cushion tables: 3, air cushion table dimensions X/Y: 1720mm/800mm, clamping fingers: 7, saw motor power: 9kW, control: Siemens PLC, system: Linux Ubuntu with graphical interface. Including adjustable scoring saw, residual cut device, safety devices, remote maintenance, optimization program Optimax and freely adjustable labels that are printed during sawing. Documentation available. An on site inspection is possible.

Crate Washing Machine

Hobart FUX-1-SAF-1

Germany

2000

used

on request

INNO30943

A Hobart pass-through crate washing machine is available. Heating type: steam, steam pressure: 8.5bar, pass-through width: 612mm, pass-through height: 440mm, washing goods: sheets, sheet dimensions X/Y: 650mm/600mm, throughput capacity: approx. 75sheets/h, infeed length: 350mm, outfeed length: 1100mm. Documentation available. An on-site inspection is possible.

Compressor

Atlas Copco GA37

Germany

2005

used

on request

INNO30942

A screw compressor Atlas Copco including an air dryer is available. Air volume flow: 5.88m³/min, max. operating pressure: 10bar, motor power: 37kW, speed: 2960rpm, operating hours: approx. 49696h. Including air dryer Atlas Copco FD 95. Documentation available. An on site inspection is possible.

Hydraulic Unit

Lippold BNK250/FCMP 200L

Germany

2012

used

on request

INNO30941

Hydraulic pump: BNK 250, Pump delivery volume: 173l/min, Motor: AC motors FCMP 200L-4/H, Motor power: 30kW, Speed: 1470rpm, Machine dimensions: approx. 2000mm/2000mm/2000mm, Weight: approx. 2000kg. Documentation available. On-site inspection is possible.

CNC Vertical Machining Center

Hurco VMX 24

Germany

2004

used

on request

INNO30940

A vertical CNC 3-axis machining center Hurco is available. Travel X/Y/Z: 610mm/510mm/610mm, table dimensions X/Y: 760mm/510mm, max. table load: 700kg, spindle interface: SK40, speed: 10000rpm, rapid traverse: 30m/min, feed rate: 15m/min. Machine dimensions X/Y/Z: approx. 3500mm/2000mm/2750mm, weight: approx. 4500kg, operating hours: 68619h. Documentation available. An on-site inspection is possible.

Eccentric Press

Schuler PDv25/200

Germany

unknown

used

on request

INNO30939

Press force: 250kN, ram stroke: 8mm-80mm, stroke rate: 180/min, installation height: 310mm, table dimensions X/Y: 550mm/400mm, ram dimensions X/Y: 355mm/220mm, machine dimensions X/Y/Z: approx. 1100mm/1400mm/2300mm, weight: approx. 2500kg. An on-site inspection is possible.

Eccentric Press

Edelhoff AZR 7

Germany

1973

used

on request

INNO30938

A single-column eccentric press Edelhoff including transfer unit is available. Press force: 130t, stroke adjustment: 30mm-130mm, ram adjustment: 75mm, stroke rate: 45/min, table dimensions X/Y: 1000mm/700mm, weight: approx. 5000kg. An on-site inspection is possible.

Hydraulic Double-Sided Press

Schön SH/LF 650

Germany

1981

used

on request

INNO30937

Press force: 650kN, Stroke: 150mm, Pressure piston diameter: 190mm, Column spacing X/Y: 950mm/460mm, Installation height: 500mm, Table dimensions X/Y: 900mm/870mm, max. stroke: 150mm, Operating pressure: 200bar, Machine dimensions X/Y/Z: approx. 1500mm/1750mm/2400mm, Weight: approx. 3000kg. Documentation available. An on site inspection is possible.

CNC Press Brake

Amada HFB 100

Germany

1999

used

on request

INNO30936

A repair-required CNC press brake Amada is available. Press force: 1000kN, max. stroke: 200mm, working width: 3100mm, passage: 2690mm, throat depth: 400mm. Machine dimensions X/Y/Z: approx. 3600mm/2100mm/2600mm, weight: approx. 6500kg, operating hours: approx. 37661h. The cylinder control has a defect. Documentation available. An on-site inspection is possible.

Column Radial Drilling Machine

Reform RB 50x16

Germany

1998

used

on request

INNO30935

Drilling capacity steel/cast iron: 50mm/60mm, spindle axis-column distance min./max.: 350mm/1600mm, spindle end-working surface distance: 350mm-1250mm, horizontal traverse: 1250mm, column arm vertical travel: 580mm, column diameter: 350mm, arm swivel: 360°, speed: 2000rpm, spindle travel: 315mm, torque: 392Nm, feed force: 15.6kN, machine dimensions X/Y/Z: approx. 2500mm/1250mm/3250mm, weight: approx. 3500kg. The coolant pump, the seal retainer and the measuring system are defective. Documentation available. An inspection on site is possible.

Eccentric Press

Helmerding EL25-B

Germany

1977

used

on request

INNO30934

An old eccentric press Elmerding with defective foot switch is available. Press capacity 30°: 25t, stroke adjustment range: 12mm-80mm, ram adjustment: 60mm, stroke rate: 120rpm, table adjustment: 150mm, safety distance: 144mm, weight: approx. 1450kg. Only 2-hand operation is possible. Documentation available. An on-site inspection is possible.

CNC Universal Milling Machine

Mikron WF 51 D/TNC 355

Germany

1988

used

on request

INNO28876

Verfahrweg X/Y/Z: 710mm/500mm/460mm, Tischabmessungen X/Y: 1000mm/500mm, Tischbelastung max: 500kg, Werkzeughalter: SK40, Drehzahl: 4000rpm, Maschinenabmessungen X/Y/Z: ca. 2000mm/2600mm/2250mm, Gewicht: ca. 3400kg, Steuerung: Heidenhain TNC 355, Betriebsstunden: ca. 34000h. Inklusive Kühlmitteleinrichtung, kompletter Arbeitsraumeinhausung, ca. 34x SK40 Werkzeughalter, Schlitten und Wellen zum Abrollen. Dokumentation vorhanden. Besichtigung vor Ort ist möglich.

Hardness Testing Machine

Zwick 3202

Germany

1969

used

on request

INNO27522

Lens magnification: 20x, aperture: 0.35, total magnification: 200x, measuring accuracy: +/-4kp/mm², average hardness value D: 144kp/mm², average thickness of reference plate: 5.9mm, max. test height: 300mm, throat depth: 135mm, machine dimensions X/Y/Z: approx. 450mm/450mm/600mm, weight: approx. 60kg. Including various lenses, clamping device for round specimens, hardness comparison plates and more. Documentation available. On-site inspection is possible.

Stirring and Whipping Machine

Lips

Germany

unknown

used

on request

INNO27513

A Lips mixer, beater and roller grater is available. Mixer: bowl volume: 40 l, dough hook, mixing blades and whisk. Whipping unit: 2x 4-finger whisks, dough hooks, 5x whisk blades, 6x whisks and 9x bowl (volume: 10l-35l). Roller unit: hopper, round bowl, square stainless steel bowl, scraper and gripper guard. Machine dimensions X/Y/Z: approx. 2350mm/900mm/1350mm, weight: approx. 900kg. Including various accessories. The wood hopper of the roller must be replaced. If required, the gas burners must be retrofitted.

Moulder

Bongard Majur Manu

Germany

unknown

used

on request

INNO27512

Dough weight min./max.: 80g/1000g, max. output: 1500 pieces/h, motor power: 0.55kW, loading height: 1360mm, output height: 850mm. Machine dimensions X/Y/Z: approx. 1010mm/850mm/690mm, weight: approx. 132kg. Overhauled: revised, new belts, new felt in infeed hopper and outfeed belt. Documentation available. On-site inspection is possible.

Drill Grinding Machine

Haarmann HSP 50

Germany

1978

used

on request

INNO27511

Max. Drilling diameter: 40mm, grinding wheel diameter: 200mm, grinding wheel width: 40mm, speed: 2800rpm, machine dimensions X/Y/Z: approx. 1200mm/850mm/1400mm, weight: approx. 350kg. Including cooling lubricant device and 10x spare grinding wheels. Documentation available. On-site inspection is possible.

Planetary Mixer

Artofex RG 10

Germany

unknown

used

on request

INNO27506

Two identical Artofex planetary mixers with a total of 7 mixing bowls are available. Stirring capacity: 100l, container volume: 100l/120l, machine dimensions X/Y/Z: approx. 800mm/1550mm/2250mm, weight: approx. 1350kg. Including 6x bowl trolleys, mass whisk, whisk, agitator blades used and new. Machine overhaul: electrics in 2021, mechanics in 2024 and oil change. On-site inspection is possible.

Dough Kneading Machine

Almac FA 90 C.I.P.

Germany

2000

used

on request

INNO30933

A continuous kneading and drawing machine Almac is available. Power: 6kW, production capacity: approx. 1000kg/h, machine dimensions X/Y/Z: approx. 3900mm/950mm/2500mm. Documentation available. An on-site inspection is possible.