Used machines Germany - Innovac GmbH

Innovac GmbH Used machines from Germany

i.e. Machining Center MORI SEIKI

Innovac used-machines

Latest Offers [1 - 20 of 2571]

Punch Laser Machine

Trumpf TRUMATIC 6000L

Germany

2001

used

on request

INNO29829

Max. cutting force: 220kN, laser power: 3200W, nitrogen connection: 30bar, oxygen connection: 20bar, connected load: 76kVA, operating hours at the beginning of 2025: 67,766h, with Trumpf TLF 3200 laser and RIEDEL L 15/21 TR3/19.00 cooler, refrigerant: R134a, filling weight: 11.5kg, high pressure: 20.2bar. Tools additionally available. An on-site inspection is possible.

Air Heater

Kroll LH 630/ LH 530/ LH 430/ LH 420/ LH 330

Germany

unknown

used

on request

INNO29828

A total of 71 Kroll air heaters are available, 30x LH 130 V10, 1x LH 130 V20, 7x LH 230 V10, 3x LH 330 V10, 1x LH 420 V10, 6x LH 430 V10, 1x LH 430 V20, 11x LH 530 V10 and 11x LH 630 V10. The fans are used and partly have bent fins and scratches. An on-site inspection is possible.

Surface Grinding Machine

Majevica BRB 75.30.2KA

Germany

unknown

used

on request

INNO29827

Longitudinal movement of the table manual drive: 750mm, longitudinal movement of the table hydraulic drive: 730mm, transverse movement of the table manual drive: 300mm, transverse movement of the table hydraulic drive: 290mm, usable surface of the table: 700x250mm, number of T-slots: 3, width of T-slots: 14mm, vertical movement of the grinding head: 400mm, division value of the grinding head manual drive: 0.01mm, distance between the inside of the grinding wheel and the column: 347.5mm, clearance under the new grinding wheel: 355mm, maximum grinding wheel diameter: 305mm, minimum grinding wheel diameter: 230mm, grinding wheel width: 25mm, grinding wheel bore: 127mm, division value of the cross table manual drive: 0.02mm, longitudinal feed of the table hydraulically: 2-25m/min, cross feed of the table stepwise, hydraulic and adjustable: 2-16mm/stroke, cross feed of the support hydraulically and continuous: 0.5-6m/min, volume of the hydraulic unit: 35l, cooling device for grinding wheel/on demand: 30l. No defects known, with documentation, an on-site inspection is possible.

Wave Soldering System

Seho 8040 PCS

Germany

1997

used

on request

INNO29826

Seho 8040 PCS with laminar and turbulent wave, preheating with heating plates and IR radiator, minimum quantity flux system, component cooler at the outlet, wave width: 400mm, max. usable working width: 390mm, max. component height: 100mm, max. PCB length: 562mm, solder nozzle: Delta B, max. wave height: 8mm, solder volume: 400kg, heating capacity solder pot: 9kW, heating-up time 20-250°C: approx. 150min, heating-up time 190-250°C: approx. 60min, preheating zone length: 700mm, three heating zones: 3x 3kW, max. preheating capacity: 9kW, transport angle: manually adjustable, 6-8°, transport speed: 0.5-2m/min, running direction: from left to right, with loading aid/slide conveyor (1000mm), unloading aid (500mm) and entry stopper for solder frame separation, exhaust connection diameter: 2x 150mm, extraction capacity per connection: 500m³/h, supply voltage (50Hz): 230/400V, rated power: 31,000W, total connected load: 18.5kW, compressed air connection: R 1/4 inch (6 bar), nitrogen connection: R 1/4 inch (6 bar). With microprocessor control PCS 96, alphanumeric display & membrane keypad (16 lines of 40 characters), 100 soldering programs, interface for host computer with visualized machine overview & BDE data backup, interface for BDE data acquisition via serial printer, control loop for transport and heating. Length: 2300mm, width: 825mm, height: 1615mm, weight without solder filling: 400kg.

CNC Machining Center

Chiron FZ 08W MAGNUM high speed

Germany

2011

used

on request

INNO29825

X-axis: 300mm, Y-axis: 250mm, Z-axis: 250mm, rapid traverse (X/Y/Z): 40/40/60m/min, chip-to-chip time: 1.5s, clamping surface dimensions: 2x 550x300mm, max. spindle speed: 15,000/min, torque: 23Nm, tool holder: HSK-A32, number of tools: 12, tool changer: CHIRON basket changer, control: GE Fanuc Series oi-MC. An on-site inspection is possible.

Stud Welding Machine

Soyer BMK-12W

Germany

2000

used

on request

INNO29822

Gun: PH-3N, voltage: 400V, weight: 50kg. Supplied with operating manual, 2x ground cables with clamp BMS/BMK, gas connection, HZ-stud holder, adapter piece and key. An on-site inspection is possible.

Electrostatic Paint Spraying System

Blo Delphin

Germany

2011

used

on request

INNO29821

The machine is in very good condition and ready for operation. An on-site inspection is possible.

Warp Beam

Liba

Germany

1991

used

on request

INNO29820

These are 21x21 inch and 30x42 inch warp beams, for direct warping and knitting mills. With documentation, without accessories. No defects known, last overhauled. An on-site inspection is possible.

Universal Oven

Memmert UF30

Germany

2020

used

on request

INNO29819

Operating temperature: 10-300°C, setting temperature: 20-300°C, setting accuracy: up to 99.9°C: 0.1°C, from 100°C: 0.5°C, temperature sensor: 1x Pt100 DIN class A, 4-wire measurement, control: Control COCKPIT Single DISPLAY, digital PID microprocessor controller with TFT color display, timer: 1 minute to 99 days, functions: SetpointWAIT, calibration of 3 temperature values, parameter selection (temperature, circulating air motor, exhaust air, program runtime, time zones), electronically controllable air turbine adjustable in 10% steps, fresh air via adjustable exhaust flap with preheating, exhaust port with throttle valve electronically controllable, logging: storage in case of power failure, programming: data logger evaluation via Ethernet, AtmoCONTROL software optional via USB, safety: electronic temperature monitoring, mechanical limiter TB, protection class 1 (DIN 12880), self-diagnosis system, internal dimensions: 400x320x250mm, volume: 32l, max. inserts: 3, max. load: 60kg, max. load per insert: 20kg, length: 650mm, width: 660mm, height: 890mm, weight: 45kg. The oven has hardly been used. An on-site inspection is possible.

CNC Lathe

Gildemeister CTX 200E

Germany

1998

used

on request

INNO29818

Base machine CTX 200E with driven tools, C-axis and 1x back working. Includes DATAPILOT software package TurnPlus, cooling unit for control cabinet, hinge belt chip conveyor, discharge height: 1100mm including coolant tank, tool holder set for universal disc turret with tool holders for external machining, boring bar holders, tools with cylindrical shank holders, sealing plugs, reducing sleeves. Bar gripper, axial complete, workpiece pick-up device, tool spindles 3x axial for drilling/milling/tapping, 1x radial for drilling/milling/tapping, 1x for saw blades, collet chuck complete for main spindle, collet chuck complete for counter spindle, 17x DIN collets 173E round Ø 3-40mm, 2x DIN collets 173E, hex SW 7 and 12mm, 2x DIN collets 173E, square SW 8mm. Bar loading magazine IEMCA BOSS 542/32, guide channel set LW 13, additionally for IEMCA BOSS 542, 13x guide jaws for bar loading magazine IEMCA BOSS 542/32, Ø 8-41mm. With complete documentation. The machine has been idle for one year as the turret head is missing, no further defects known, operating hours unknown, without maintenance records. With bar loader and numerous tools.

Planing and Moulding Machine

Kuper SWT XL-2

Germany

2021

used

on request

INNO29817

Working width (with tool diameter 125mm): 15-230mm, working height (with tool diameter 125mm): 10-150mm, minimum workpiece lengths: min. single piece: 800mm, min. piece by piece: 300mm, spindle arrangement: top, top, 1st spindle (horizontal top): Siemens IE3 motor with inverter brake 7.5kW (10 HP), diameter: 40mm, spindle length: 235mm, speed frequency-controlled: 4000-6000/min, tool cutting circle: 112-200mm, axial adjustment: 20mm, pressure shoe: pneumatic, dynamically adjustable, standard profile depth: 20mm, suction nozzle diameter: 125mm, suction: individually adjustable, tool clamping system: Pro-Lock. Feed system: chain system, each roller unit with its own gearbox and cardan shaft, feed motor with electronic brake 4kW (5 HP), digital display feed speed: 6-24m/min, motorized height adjustment of the feed carrier, two driven infeed rollers before the first lower spindle, pneumatically selectable up/down, roller spacing shortened by feed cassette, tool change swing-away. Machine electrics: 400V/ 3 phases/ PE, main switch: 3-pole, 50Hz, IP 54, installation according to current standards. Machine frame/tables: heavy machine frame, torsion-free and low-vibration, all machine tables hard-chromed, infeed and outfeed table: driven, double-bearing table roller. Manual lubricant pump additional equipment (selection): motorized radial adjustment of the upper spindles, reset button in the control cabinet, support table 1100mm, right-hand support fence with guide rollers, roller spacing 100mm, infeed funnel on the support table: feed speed 2-18m/min adjustable via potentiometer. Additional feed rollers in the infeed area, rubber-coated feed rollers instead of steel rollers, extended side pressure, max. spindle speed: 9000/min (high-performance bearings), pressure lips pneumatically sprung and adjustable, spindle motor power: 11kW, relay control of the machine: automatic shutdown in case of fault. Operating hours: under 500h. With documentation, an on-site inspection is possible.

CNC Universal Milling Machine

Deckel Maho DMU 50T

Germany

1998

used

on request

INNO26767

Spindle speed range: 9000rpm, travel X/Y/Z: 500mm/400mm/400mm, feed rate: 10000mm/min, rapid traverse: 12m/min. Table dimensions X/Y: 700mm/500mm, max. table load: 200kg, number of T-slots: 7, distance between T-slots: 63mm. Control: Heidenhain, tool changer: 16-fold, dimensions X/Y/Z: 4000mm/2200mm/2450mm, weight: approx. 3500kg.

Disc Finishing Machine

Otec CF2x18

Germany

2023

used

on request

INNO29816

Basic equipment: thermally cross-linked wear-resistant PU working container lining (profiled), rotary table with flow-optimized carrier bars for sensitive workpieces, complete water drainage via stainless steel hollow shaft for wet processing, high-precision bearing of the rotary table (with corrosion-resistant ceramic sealing system for wet processing), 2x drive motor 0.9kVA with thermal protection, machine frame in steel construction. Control of the machining process via PLC with display of processing time, table speed, compound dosing, start delay, process interruption and operating hours, setting of time and speed parameters via touchscreen, start/stop buttons for program sequence, storage of 500 machining programs, table speed control via frequency converter, main switch/reset switch, with signal light green/yellow/red, with USB interface. 2x working containers each with 18l container volume, container inner diameter: 330mm. Operating voltage: 230/400V (slip gap operation), 50/60Hz, VS max. 16A, control voltage: 24V, protection class: IP 54, color: RAL7012 basalt grey and RAL7035 light grey, containers in RAL 5002, standards: VDE, UVV, CE, control cabinet with touchscreen CF 2x18 ZGZG, control: S7/1200, 2x working containers CF 18 ZG round ribs + PU-R, ceramic ring, for gapless operation of the working container during wet processing, 2x lids for working container CF 18 wet, water connection without valve, CF-9/18, connection diameter: 13mm, for removal of dirt particles from fresh water and circulation, longer service life for flow meter, 2x dosing unit WZG 2 CF 9/18, compound drawer 1 CF - 9/18, extension without hand sieves CF 2x18. Connected load: 2kVA, weight: 330kg. With documentation, without accessories. An on-site inspection is possible.

Spur Gear

Sew-eurodrive SDGA-1105 SP

Germany

2021

used

on request

INNO29815

Lifting capacity: 52t, drive shaft diameter of the hollow shaft: 245mm, brake shaft dimensions: 100x190mm, drive shaft dimensions: 80x140mm, ambient temperature: -15 to 45°C, center distance: 1105mm, rated power: 275kW. The gear is still unused. An on-site inspection is possible.

Double Mitre Saw

Elumatec DG104

Germany

2006

used

on request

INNO29814

Smallest cutting length at 90°: 350mm, smallest cutting length at 45° inclined: 350mm, swiveling range inward: 90-45° (down to 22.5° manually with digital display), tilting range inward pneumatically: 90-45°, saw blade diameter: 420mm, saw blade speed: 2800/min, electrical connection: 230/400, power output per motor: 4kW, compressed air connection: 7bar, air consumption per working cycle: 40l without spraying, 64l with spraying, length: 4380mm, width: 2871mm, height: 1985mm. With complete documentation, without accessories. An on-site inspection is possible, but not under power. The machine is already dismantled and ready for loading. No defects known, was regularly maintained by the manufacturer.

Automatic Folder Gluer

Eterna EFOLD 1100 ELITE

Germany

2020

used

on request

INNO29813

Features: belt feeder, Ero gluing system (cold glue, 4 nozzles), folding unit, pressing belt, max. sheet size: 60-800x126-1100mm, production possibilities: straight line, crash lock bottom, 4- and 6-corner, double-wall boxes and file covers/piches/envelopes, board thickness: 200-800g/m², corrugated board: N-, E-, F-flute, max. belt speed: 320m/min, shaking speed: 20m/min, main motor power: 11kW, total power requirement: 35kVA, max. air consumption: 0.7m³/min, length: 12,700mm, width: 2600mm, weight: 7t. Operational hours counter: 1494h. An on-site inspection is possible.

Flat Bed Punching and Embossing Machine

Heidelberger Druckmaschinen Promatrix 106 CS/CSB

Germany

2021

used

on request

INNO29812

Features: automatic non-stop delivery with conveyor, non-stop feeder with rods, pull mark left, push mark right, quick clamping frame for tooling, lower stripping station, upper stripping station, two exchange frames for lower stripping station. Without die-cutting plates. Processable materials: min. paper 90g/m², max. solid board 2000g/m², max. corrugated board/ with MasterSet 4/ 2mm, max. sheet size 760x1060mm, min. sheet size/with MasterSet 300x350/ 350x400mm, max. cutting pressure: 2.6MN/ 260t, max. machine speed: 8000 sheets/h, max. feeder pile height without non-stop/ in non-stop operation: 1500/ 1200mm, max. feeder pile weight: 1500kg, max. delivery pile height: 1400mm, max. delivery pile weight: 900/ 1340kg. Operating hours: 1525h. An on-site inspection is possible.

Spark Erosion Machine

Wagner Maschinen DM-323

Germany

1988

used

on request

INNO29811

Two DM-323 electrical discharge machines are available. Operating hours machine 1/2: 12,134.51 / 32,704.5 h. Operating manuals and circuit diagrams available. An on-site inspection is possible.

Low-Voltage Motors

Siemens SIMOTICS SD 1LE5/ 1LE1

Germany

2021

used

on request

INNO29810

A total of 12 low-voltage motors are available, 4x SIMOTICS SD 1LE5 and 8x SIMOTICS SD 1LE1. (1) SIMOTICS SD 1LE5, Motor type: Three-phase asynchronous motor, low voltage, cast iron housing, Severe Duty series SIMOTICS SD (model range 1LE5), protection class: standard IP55, insulation class: Class F, operating mode: continuous duty S1 according to IEC/DIN EN 60034-1, environment: -20°C to 40°C, up to 1000m above sea level. (2) SIMOTICS SD 1LE1, rated voltage: standard voltages, operating mode: continuous duty S1, housing: cast iron (Severe Duty), cooling: self-ventilated, insulation class: F (temperature class 155 / utilization B), speed range: 750-3600/min, max. rated torque: approx. 1703 Nm. The motors are still unused, the year of construction is 2021/22. An on-site inspection is possible.

Lathe

Meuser M1 P

Germany

unknown

used

on request

INNO29809

Speed: 45-1800/min, the machine is functional. An on-site inspection is possible.