▷ Used other machines from Germany | innovac.de

Innovac GmbH Used machines from Germany

i.e. Machining Center MORI SEIKI

All Offers / Other machines

Ceramics, stones and minerals 4 Glass machinery 21 Municipal technique 2 Special machines 6 Vacuum technology 2 Waste disposal, recycling 24 Wastewater treatment 1

Innovac used-machines

Other machines [1 - 20 of 60]

Pallet Centrifugal Drying System

Kitzinger Maschinenbau Gmbh conrion

Germany

2018

used

on request

INNO32647

Offered is a pallet spin drying system with infeed roller conveyor. Equipped with a stainless steel roller conveyor, enclosed machine housing, safety guard, control panel with emergency stop button, signal light and pneumatic components. Inspection possible by arrangement.

Shredder

Lindner Jupiter 3200

Germany

2010

used

on request

INNO32590

A shredder with control cabinet, three spare motors and discharge conveyor is available: 1) Lindner Jupiter 3200 shredder, dimensions: 6500x2500x3200mm, weight: 36t, operating hours: 58545h, with hopper, operator panel and hydraulic power unit. 2) Control cabinet for Jupiter 3200, dimensions: 3000x2000x600mm, weight: 980kg, with frequency converter, water cooling units and recooling unit. 3) Spare motor ABB M3BP 315LKA 6, power: 160kW, speed: 994rpm, IE3, dimensions: 1200x800x600mm, weight: 1.41t, is unused. 4) 2x spare motor Schorch 315L IMB3, power: 160kW, speed: 988rpm, dimensions: 1200x800x600mm, weight: 1.3t. 5) Inclined conveyor FC H101 1200/9200, dimensions: 9200x1500x1800mm, weight: 1.7t. The machine was regularly serviced by the manufacturer. During annual rotor maintenance, the rotor was fully hardfaced. The track was retensioned every three months. New motors with energy efficiency class IE3 were installed in 2021. The foreign object flap was replaced in 2024. Two couplings were replaced in 2024. The machine is operational. An on-site inspection is possible. The machine is not connected to the power supply.

Natural Gas Filling Station

Schwelm Anlagentechnik

Germany

2016

used

on request

INNO32527

Gas supply: natural gas from the public gas network, gas treatment: drying using a molecular sieve, max. refueling pressure: 300bar(g), natural gas compressor station capacity: 630m³, storage type: SP28, storage pressure: 300bar(g), inlet pressure: 2.5-700mbar(g), storage type: SP28, storage volume: 2.24m³, storage pressure: ≤300bar(g), compressed air/gas supply (Pₛ,in/Pₛ,out,EGT): 1bar(g)/300bar(g), temperature range: -10 to 50°C/-10 to 60°C, volume flow rate: 74-113Nm³/h, power consumption: 36kW, noise level: 65dB(A) at a distance of 1m, length: 4,850mm, width: 2,690mm, height: 3,100mm, weight: approx. 30t, including documentation.

Pyrolysis Plant

Pyreg P500

Germany

2020

used

on request

INNO32447

Design: modular containerized system, process: continuous pyrolysis/thermochemical carbonization, reactors: 2, feedstocks: wood/landscape maintenance material/biomass, thermal output: approx. 150kW, biochar production: approx. 300t/year, operating mode: autothermal, flue gas recirculation: available, burner: FLOX, discharge: water-cooled and airtight, degree of automation: fully automatic, control: Siemens S7-300, operator panel: Siemens TP1200 Comfort, automatic mode operating hours: approx. 7069h. Process container dimensions X/Y/Z: approx. 9000mm/3000mm/2800mm, process container weight: approx. 14t, flue gas treatment container dimensions X/Y/Z: approx. 3000mm/3000mm/2800mm, flue gas treatment container weight: approx. 4t. Including Bruns walking floor container with approx. 30m³ dosing hopper, inclined screw conveyor, bagging station and conveying spirals. A drying system for wood chips is optionally available. Documentation available. An on-site inspection is possible.

Contour Wire Saw

Baumunk KSSF 2000 UNIKONTUR

Germany

2000

used

on request

INNO32409

A Baumunk contour wire saw in need of repair is offered. Drive power: 5.5kW, control: Bosch OSA. The machine has been idle for about one year. Contour sawing was still working well when last used. The mounting for the grinding rollers is defective. Inspection by appointment possible.

Roller Furnace

Studio 1 ST1 FRM 9/1200/1250°

Germany

1997

used

on request

INNO32314

Suitable for firing ceramics and clay, number of burners: 10+1, fuel: natural gas or liquefied petroleum gas (LPG), connected load: 8kW, length: 8800mm, width: 2200mm, height: 2300mm, with control cabinet, control panel and spare parts, the machine has few operating hours, an on-site inspection is possible.

Horizontal Baling Press

Hsm AK 10/900

Germany

1987

used

on request

INNO32303

Press force: 10t, loading aperture dimensions X/Y: 580mm/900mm, bale width/height: 500mm/600mm, bale weight depending on material: approx. 100kg, motor power: 6.8kW, Control system: Siemens SIMATIC S5-100U. Machine dimensions X/Y/Z: 4700mm/1000mm/1540mm, weight: approx. 1200kg. The machine has been overhauled and is in good condition. Documentation available. An on-site inspection is possible.

Bale Press

Hsm 155.2 VL

Germany

2001

used

on request

INNO32062

Press force: 16t, Feed opening dimensions X/Y: 1100mm/590mm, Chamber dimensions X/Y/Z: 1100mm/700mm/1130mm, Bale dimensions X/Y/Z: 1100mm/700mm/950mm, Max. bale weight: 200kg, Tying: 4-way vertical, Throughput: approx. 4-8 bales/h, Machine dimensions X/Y/Z: approx. 1450mm/950mm/2400mm, Weight: approx. 950kg. No UVV inspection and the hydraulic oil has been drained. The baler has not been cleaned. An on-site inspection is possible.

Glass Cutting System

Hegla VSG-A 46 MT

Germany

2002

used

on request

INNO31843

A Hegla glass cutting system will be available approximately from December 2026. Direction of travel: right-left, connected load: 35kW, max. glass sheet dimensions X/Y: 4600mm/3210mm, max. single glass thickness: 16mm, machine dimensions X/Y/Z: approx. 13200mm/6000mm/1000mm. The stops are worn. Documentation available. An on-site inspection is possible.

Bale Press

Mac Fab MF LH300

Germany

2020

used

on request

INNO31698

A paper and cardboard baling press Bema is available. Motor power: 2.2kW, pressing force: 20t, opening dimensions X/Y: 596mm/1200mm, bale dimensions X/Y/Z: 1200mm/800mm/1000mm, max. bale weight: 300kg, cycle time: 40s, hydraulic oil filling: 24l, machine dimensions X/Y/Z: approx. 1800mm/1100mm/1950mm, weight: approx. 1150kg. Documentation available. An on-site inspection is possible.

Glass Furnace

Efco Furnaces 2400 x 4200 Glass Temp

Germany

1997

used

on request

INNO31677

A complete Efco furnace system for the production of tempered safety glass is available. Heating capacity: 814.5kW, max. glass pane dimensions X/Y: 2400mm/4200mm, max. temperature: 750°C, total system length: approx. 25m. Components: loading section, furnace, cooling section, unloading section. Documentation available. An on-site inspection is possible.

Vertical Baling Press

Hsm V-Press 818

Germany

2012

used

on request

INNO31618

Pressing force: 185kN, filling opening dimensions: 1195x541mm, max. bale weight depending on material: 200kg, max. bale dimensions: 1200x780x700mm, throughput capacity: 2 to 5 bales/h, idle cycle time: 35s, strapping: 4 fold with polyester strap, pressing capacity at idle: 68m³/h, pressing chamber dimensions: 1200x780x1300mm, voltage: 3x 400V, motor power: 3kW, length: 1700mm, width: 1046mm, height: 2370mm, weight: 994kg. An on site inspection is possible.

Glass Cutting System

Lisec ESL-60/30RS

Germany

1998

used

on request

INNO31247

A CNC glass cutting system Lisec in need of repair is available. Glass thickness range: 3mm-12mm, min. glass dimensions X/Y: 1600mm/1600mm, max. glass dimensions X/Y: 6000mm/3210mm, max. cutting speed: 120m/min, max. transport speed: 40m/min, cutting accuracy: +/-0.15mm, max. table load: 35kg/m², max. payload: 600kg, weight: approx. 6400kg. The X-axis of the machine has a fault. The system can cut diagonally and circularly and automatically grind the glass edges. Documentation available. An on-site inspection is possible.

Vacuum Angle Valve

Leybold BAV DN800 ISO-F EP VA

Germany

unknown

used

on request

INNO31055

Two like-new and partly originally packaged large-format vacuum angle valves Leybold are available. Deflection: 90°, nominal diameter: 800mm, max. operating pressure: 7bar. Documentation available. An on-site inspection is possible.

Shredder

Burghardt PS Starter

Germany

2021

used

on request

INNO30995

A Burghardt cardboard shredding machine is available. Cutting width: 320mm, max. cardboard thickness: 12mm, throughput capacity: approx. 2m³/h, operating speed: 10m/min, motor power: 0.75kW, machine dimensions X/Y/Z: approx. 500mm/600mm/650mm, weight: approx. 100kg. Documentation vorhanden. An on-site inspection is possible.

Dewatering Machine

Hiller DCH76-402

Germany

2010

used

on request

INNO30966

A Hiller two-phase centrifuge for solid-liquid separation and dewatering is available. Drum speed: 2700rpm, max. operating speed: 2650rpm, max. feed material density: 1.3kg/dm³, drum inner diameter: 752mm, drum wall thickness: 20mm, drum material: 1.4470, max. operating temperature: 50°C, max. operating pressure: 0bar, motor power: 75kW. Machine dimensions X/Y/Z: approx. 5100mm/2300mm/1750mm, weight: approx. 11600kg. Documentation available. An on-site inspection is possible. Image is an example.

Sand Blasting Machine

S.a.g. T3/T4

Germany

2005

used

on request

INNO30958

Two glass sandblasting systems from S.A.G. are available. 1) S.A.G. T4, year of construction: 2005, arrangement: vertical, max. blasting width: 3000mm, max. blasting height: 2250mm, max. glass height: 2400mm, glass thickness range: 3mm-40mm, blasting capacity: approx. 15m²/h, machine dimensions X/Y/Z: approx. 3800mm/3300mm/1900mm, weight: approx. 1550kg. 2) S.A.G. T3, year of construction: 2002, blasting width: 2800mm, blasting height: 1200mm, glass thickness range: 3mm-40mm, machine dimensions X/Y/Z: approx. 4100mm/2300mm/1900mm, weight: approx. 1350kg. Documentation available. An on-site inspection is possible.

Shredder

Erdwich M600/1-600

Germany

2021

used

on request

INNO30878

A single-shaft shredder Erdwich for contaminant-free red brass and brass chips is available. Cutting unit dimensions X/Y: 600mm/500mm, height: 300mm, knife width: 25mm, screen hole diameter range: 25mm-35mm, machine dimensions X/Y/Z: approx. 1600mm/650mm/800mm, weight: approx. 600kg. Documentation available. An on-site inspection is possible.

Glass Grinding Machine

Knopp Glaskant-Combi

Germany

1992

used

on request

INNO30740

An old Knopp glass grinding machine for edge processing is available. Grinding belt dimensions X/Y: 1830mm/100mm, glass types: float glass/mirror glass/furniture glass/table tops, grinding wheel diameter: 200mm, table dimensions X/Y: 900mm/1400mm, machine dimensions X/Y/Z: approx. 1300mm/1500mm/1700mm, weight: approx. 500kg. On site inspection is possible.

Shredder

Vecoplan VAZ 1300 M KN

Germany

2008

used

on request

INNO30680

A large-format single-shaft shredder Vecoplan is available. Rotor diameter: 370mm, effective rotor length: 1300mm, speed: 120rpm, knife rows: 37, knife dimensions X/Y: 40mm/40mm, feed opening X/Y: 1400mm/1300mm, hopper volume: approx. 3m³. Machine dimensions X/Y/Z: 3200mm/2400mm/1500mm, weight: approx. 5500kg. An on-site inspection is possible.