Maszyna do formowania wtryskowego

Arburg ALLROUNDER CENTEX 470C 1500-350/150

Niemcy

2005

używany

na żądanie

INNO32310

Clamping force: 1500kN, rated current: 133A, connected load: 74kW, an on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Krauss Maffei KM 65-380 CX

Niemcy

2008

używany

na żądanie

INNO32309

Clamping force: 650kN, length: 4000mm, width: 1600mm, height: 2200mm, weight: 3.9t, an on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Krauss Maffei KM 160-1000 CX

Niemcy

2005

używany

na żądanie

INNO32308

Clamping force: 1600kN, width: 1600mm, height: 2200mm, weight: 6.8t, an on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Demag Ergotech 1250-440 concept

Niemcy

2001

używany

na żądanie

INNO32307

Clamping force: 1250kN, tie-bar spacing: 475x450mm, injection unit: 440, max. flow rate: 100l/min, max. hydraulic pressure: 190bar, weight: 6.6t, an on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Demag Ergotech Extra 80-430

Niemcy

2004

używany

na żądanie

INNO32306

Clamping force: 800kN, tie-bar spacing: 400mm, injection unit: 430, max. flow rate: 76l/min, max. hydraulic pressure: 210bar, control: CDIAS, weight: 3.6t, an on-site inspection is possible.

więcej

Wtryskarka do tworzyw termoplastycznych

Polyapress

Niemcy

nieznany

używany

na żądanie

INNO32260

Condition: used, with visible signs of use, was operational until placed in storage, control voltage: 24V, operating voltage: 230V, frequency: 50Hz, CO₂ pressure: 10bar, connected load: 500W, with CE marking. An on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Battenfeld TM 4500/3300

Niemcy

2004

używany

na żądanie

INNO32239

A BATTENFELD large-format horizontal injection molding machine in need of repair is offered. Operating pressure: 210bar, clamping force: 4500kN, screw diameter: 85mm, injection volume: 2128cm³, injection pressure: 1624bar, tie-bar spacing X/Y: 900mm/800mm, opening stroke: 950mm, max. mold height: 970mm, oil capacity: 900l, connected load: 55kW, operating hours: approx. 82510h, weight: approx. 20.4t. The servo motor for the screw drive is defective. In addition, some smaller parts are missing. An on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Demag IntElect 150/520-410

Niemcy

2008

używany

na żądanie

INNO32228

A Demag all-electric injection molding machine with Wittmann 3-axis robot and safety enclosure is offered. Clamping force: 1500kN, locking force: 1650kN, max. mold opening stroke: 495mm, min./max. mold height: 275mm/585mm, max. distance between mold platens: 1080mm, mold platens X/Y: 770mm/770mm, clear distance between tie bars X/Y: 520mm/520mm, max. mold weight: 1700kg, max. mold weight on the movable mold platen: 1150kg, ejector stroke: 125mm, ejector force: 35kN, ejector retraction force: 35kN, screw diameter: 35mm, L/D ratio: 20, max. injection pressure: 2430bar, stroke volume: 166cm³, shot weight: 146g, max. metering stroke: 173mm, max. nozzle stroke: 400mm, nozzle immersion depth: 20mm, nozzle contact force: 30kN, installed barrel heating capacity: 9.4kW, material hopper capacity: 35l, control: CDIAS, operating hours: approx. 76000h, machine weight: approx. 7400kg. Including WITTMANN 3-axis robot, year of manufacture: 2006, travel X/Y/Z: 550mm/1200mm/2000mm, robot weight: approx. 240kg as well as safety enclosure and 1 × core pull preparation AS. Documentation available. An on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Arburg 320C 500-170 Golden Edition

Niemcy

2006

używany

na żądanie

INNO32196

Clamping force: 500kN, tie-bar spacing: 320x320mm, cylinder diameter: D30, control: Arburg SLOGICA, automatic operating hours: 63.147h, pump operating hours: 65.755h, semi-automatic operating hours: 14h, cycles: 13.943.435. An on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Arburg ALLROUNDER 270C 300-100 control+

Niemcy

2003

używany

na żądanie

INNO32195

Clamping force: 300kN, tie-bar spacing: 270x270mm, cylinder diameter: D15, control: Arburg Control+, automatic operating hours: 63.212h, pump operating hours: 63.212h, cycles: 15.328.195. An on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Engel Victory 1050/180 tech

Niemcy

2014

używany

na żądanie

INNO32166

Clamping force: 1800kN, opening force: 96kN, max. opening stroke: 750mm, min. mold height: 300mm, max. platen distance: 1050mm, clear tie-bar spacing: tie-bar-less, mold mounting platens X/Y: 880mm/830mm, max. mold weight: 1500kg at center of gravity 230mm, ejector stroke: 180mm, ejector force forward/backward: 80kN/33kN, screw diameter: 55mm, metering stroke: 215mm, max. stroke volume: 510cm³, injection rate: 255cm³/s, max. injection pressure: 2050bar, nozzle stroke: 350mm, nozzle contact force: 67kN, injection unit heating capacity: 16.3kW, heating zones incl. nozzle: 5, barrel: M9 bimetallic barrel, integrated hot runner control zones: 24×220V, mold cooling circuits: 6×10l/min, hydraulic oil capacity: approx. 540l, operating hours: 67423h (as of 30.06.2026). The machine will be available from December. Machine dimensions X/Y/Z: approx. 6275mm/1888mm/2100mm, weight without mold: approx. 12200kg. Documentation available. An on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Engel e-victory 440/180

Niemcy

2017

używany

na żądanie

INNO32156

Clamping force: 1800kN, max. opening stroke: 750mm, min. mold installation height: 300mm, screw diameter: 40mm, L/D: 20, G4 S10, clear tie-bar spacing: tie-barless, max. stroke volume: 220cm³, injection rate: 223cm³/s, max. injection pressure: 1930bar, material barrel: M9 (bimetallic barrel), length: 6455mm, height: 2100mm, weight without mold: 13.7t, operating hours: 59,947h, with documentation. Available from December 2026, an on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Arburg Allrounder 320-210-850

Niemcy

1991

używany

na żądanie

INNO32145

A repair-needing Arburg injection moulding machine is offered. Clamping force: 850kN, distance between tie bars X/Y: 320mm/320mm, mould mounting platens X/Y: 490mm/490mm, min. mould height: 250mm, max. opening stroke: 375mm, max. platen daylight: 625mm, ejector stroke/force: 150mm/38kN, screw diameter: 35mm, max. stroke volume: 144cm³, max. shot weight PS: approx. 120g, max. injection pressure: 1500bar. Machine weight: approx. 2500kg. Heater was removed, hydraulic pump runs unevenly. An on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Arburg 375V 500-100

Niemcy

2008

używany

na żądanie

INNO32126

A vertical injection moulding machine from ARBURG is offered. Clamping force: 50t, table size X/Y: 500mm/420mm, max. shot volume: 65cm³, min. opening width: 272mm (172mm), max. opening width: 522mm (422mm), hydraulic/pneumatic cascades: 2/4, hydraulic/pneumatic core pulls: 0/0, hydraulic operating hours: 6979h, automatic operating hours: 4696h, total cycles: 142609. Including shuttle table. Documentation available. Inspection possible by arrangement.

więcej

Maszyna do formowania wtryskowego

Krauss Maffei KM 550/ 3000 GX 550

Niemcy

nieznany

używany

na żądanie

INNO32101

The injection momlding machine corresponds to the hydromechanical two-platen series, clamping force: 550t, operating hours: approx. 80h, with Handling Krauss Maffei KM 250/ LRX-S 250. An on-site inspection is possible, the machine is located in Mexico.

więcej

Maszyna do formowania wtryskowego

Krauss Maffei KM650/3000CX

Niemcy

2010

używany

na żądanie

INNO32068

A fully hydraulic large-format two-platen injection molding machine from Krauss Maffei with an LRX350 linear robot is available. Clamping force: 6500kN, injection unit: SP3000, screw diameter: 70mm, L/D ratio: 22.9, max. injection pressure: 2389bar, shot volume: 1232cm³, shot weight: 1121g, injection rate: 462cm³/s, screw speed: 285rpm, plasticizing rate: 108.6g/s, nozzle contact force: 129kN, mold opening force: 345kN, mold opening stroke: 1150mm, min. mold height: 600mm, max. daylight opening: 1750mm, ejector stroke: 250mm, ejector force: 95kN, max. mold weight: 11400kg, clear distance: 1200mm/1120mm, platen dimensions X/Y: 1510mm/1370mm. Robot payload: 35kg, travel X/Y/Z: 1200mm/2000mm/4000mm, conveyor dimensions X/Y: 2500mm/800mm, discharge height: 1000mm, max. conveyor belt temperature: 70°C. Machine dimensions X/Y/Z: approx. 8000mm/3000mm/2700mm, weight: approx. 31t, operating hours: approx. 75900h. Documentation available. An on-site inspection is possible. Available from approximately November 2026.

więcej

Maszyna do formowania wtryskowego

Arburg Allrounder 570 A 2000-800

Niemcy

2010

używany

na żądanie

INNO32019

Three similar Arburg injection molding machines are available. 1) Arburg ALLROUNDER 570 A 2000-800, year of manufacture: 2010, clamping force: 2000kN, distance between tie bars: 570mm/570mm, pressure: 575bar, control system: Selogica direct 4.090, operating hours: 91917h, weight: approx. 9800kg. 2) Arburg ALLROUNDER 570 A 2000-800, year of manufacture: 2011, clamping force: 2000kN, distance between tie bars: 570mm/570mm, pressure: 575bar, control system: Selogica direct 4.090, operating hours: 82736h, weight: approx. 9800kg. 3) Arburg ALLROUNDER 570 A 2000-800, year of manufacture: 2011, clamping force: 2000kN, distance between tie bars: 570mm/570mm, pressure: 575bar, control system: Selogica direct 4.090, operating hours: 90722h, weight: approx. 9800kg. Documentation available. An on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Battenfeld BK-T 1000/400

Niemcy

1994

używany

na żądanie

INNO31953

A hydraulic Battenfeld plastic injection molding machine is offered. Clamping force: 1000kN, screw diameter: 40mm, shot weight: approx. 183g, mold mounting platens X/Y: 700mm/700mm, shot volume: 201cm³, max. injection pressure: 1968bar, max. screw speed: 290rpm, nozzle contact force: 79.2kN, machine cycles: approx. 1985087, operating hours: approx. 53578h, control system: Battenfeld UNILOG 4000. Dimensions: approx. 5440mm/1550mm/2300mm, weight: approx. 5060kg. Motor, pump and inverter renewed in December 2009. An on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Arburg Allrounder 375 V 500-170

Niemcy

2011

używany

na żądanie

INNO31680

A virtually new and almost fully equipped Arburg vertical injection molding machine from a laboratory is available, where its plasticizing unit was never used. Clamping force: 500kN, opening force: 30kN, opening stroke: 250mm, ejector force: 30kN, ejector stroke: 70mm, screw diameter: 25mm/30mm/35mm, nozzle contact force: 50kN, nozzle retraction stroke: 210mm, heating capacity: 9kW, heating zones: 5, hopper volume: 25l, technology level: T2, rotary table diameter: 900mm. Machine dimensions X/Y/Z: approx. 3400mm/2050mm/3500mm, weight: approx. 4200kg, operating hours: 9201h, machine cycles: approx. 120k. The machine was used exclusively for composite materials such as carbon fiber and Kevlar. Documentation available. An on-site inspection is possible.

więcej

Maszyna do formowania wtryskowego

Krauss Maffei 650-5700 CM

Niemcy

1999

używany

na żądanie

INNO31654

A large-format injection molding machine Krauss Maffei is available. Clamping force: 6500kN, tie bar spacing X/Y: 1000mm/930mm, platen dimensions X/Y: 1530mm/1450mm, max. opening stroke: 900mm, mold height range: 350mm-650mm, max. platen spacing: 1550mm, ejector stroke: 250mm, ejector force: 110kN. Machine dimensions X/Y/Z: approx. 10000mm/2800mm/2450mm, weight: approx. 46000kg. Including a Wittmann handling unit. Documentation available. An on-site inspection is possible.

więcej

Wszystkie oferty / Przetwórstwo tworzyw sztucznych / Maszyny do formowania wtryskowego