Hydrauliczna prasa jednokolumnowa

Hymag HE 6 TME SO 6

Niemcy

2003

używany

na żądanie

INNO32533

Pressing force: 63kN, stroke: 300mm, motor power: 7.5kW, on-site inspection is possible.

więcej

Maszyna do rozwijania, prostowania i wykrawania

Pbk Automation

Niemcy

1995

używany

na żądanie

INNO32532

A decoiling, straightening and stamping line with roller feed, straightening machine, decoiler and hydraulic press is available, 1) Roller feed WV-U-80/DSM 300 P-N, working direction: left to right, max. strip width: 300mm, strip thickness: 0.1-5mm, max. strip cross-section: 1,000mm², roller diameter: 80mm, max. feed speed: 120m/min, max. roller contact force: 4.5kN, feed accuracy: ±0.05mm, adjustable pneumatic pressure: approx. 5bar, 2) Straightening machine RSTC W60/7/300, working direction: left to right, passage width: 320mm, max. strip width: 300mm, strip thickness: 0.4-5mm, max. strip cross-section: 1,050mm², straightening and correction roller diameter: 60mm, feed roller diameter: 80mm, strip speed: 0-30m/min, feed rollers: 4, straightening rollers: 7, correction roller: 1, drive power: 3kW, 3) Decoiler E 3000/300 OMB, working direction: left to right, max. load capacity: 30kN, expansion range: 470-520mm, max. coil outer diameter: 1,500mm, strip width: 300mm, main shaft height above floor: 1,000mm, weight: 1.2t, 4) Hydraulic Single-Column Press Dunkes, pressing force: 125t, including documentation. On-site inspection is possible.

więcej

Szlifierki bezkłowe do wałków

Paragon Machinery RC-1812

Niemcy

2002

używany

na żądanie

INNO32529

Grinding wheel dimensions: 455x305x229.6mm, grinding diameter: 2-50mm, length: 2,450mm, width: 2,100mm, height: 1,600mm, weight: 3.7t, operating hours: unknown, including documentation, tooling package and clamping devices, out of operation since 2023. On-site inspection is possible.

więcej

Stół szlifierski

Rippert Anlagentechnik ST 20-250

Niemcy

2018

używany

na żądanie

INNO32526

Working width: 2,500mm, air flow rate: 1,600m³/h, motor power: 1.5kW. Equipment: integrated under-table extraction system, radial fan with spark protection, filter elements below the wooden grate, pneumatic filter cleaning, direct air recirculation, wooden grate with defined gap spacing, galvanized and painted sheet steel, integrated motor protection switch and compressed air supply, CE marking. On-site inspection is possible.

więcej

Jednostka filtracyjna, odciągowa i zasilająca

Kist & Escherich ESUC 1300

Niemcy

2024

używany

na żądanie

INNO32525

Max. volume flow rate: 1,260m³/h, possible number of filter stages: 1, 2, operating voltage: 3x 400V, PE, N, frequency: 50Hz, rated power: 1.8-2.9kVA, max. rated current: 2.7-6.6A, upstream fuse: 16A, mains connection three-phase AC: 400V, max. rated power: 2.9kVA, max. rated current: 6.6A, upstream fuse: 16A, control cabinet protection rating: IP54, max. differential pressure: 2,380Pa, compressed air quality: factory-supplied, oil-free, dry, max. inlet operating air pressure: 8bar, operating temperature: 5-40°C, weight: 165kg. On-site inspection is possible.

więcej

Kompaktowe centrum obróbcze CNC

Spinner VC810-II

Niemcy

2004

używany

na żądanie

INNO32524

X-axis travel: 810mm, Y-axis travel: 610mm, Z-axis travel: 610mm, rapid traverse: 30m/min, tool holder: SK40/DIN 69871A, pull stud: DIN 69872A, tool changer: 32 tools, program memory expansion: 64MB (ATA memory card), machine color: RAL 7035/5008, mains voltage: 400V, mains connection: 3/PE~ (three-phase AC with protective earth), mains frequency: 50/60Hz, operating current (I_B): 50A, rated current (I_N): 50A, programming interface: Siemens ShopMill, max. spindle speed: 8,000rpm, screen: 10.4-inch color display, control system: Siemens 810DE PowerLine, operating hours: 37,506h, including documentation. On-site inspection is possible.

więcej

Tokarka CNC

Spinner TC 800 110 MC

Niemcy

2009

używany

na żądanie

INNO32523

X-axis travel: 360mm, Z-axis travel: 980/1580mm, rapid traverse X/Z: 15/24m/min, max. turning diameter: approx. 500mm, max. swing diameter: 800mm, spindle nose: A11, bar capacity: 110mm, power (100%/40%): 22/33kW, torque gear stage 1: 175/263Nm, torque gear stage 2: 700/1,050Nm, turret type: servo turret, tool stations: 12, tool holder: VDI 50, number of driven tools: 12, driven tool speed: 4,000rpm, power (100%/40%): 5/9.6kW, axial torque (100%/40%): 18/35Nm, radial torque (100%/40%): 15/28.8Nm, hydraulic tank: 11l, central lubrication reservoir: approx. 2-3l, mains connection: 3/PE~ 400V, frequency: 50/60Hz, operating current (I_B): 63A, rated current (I_N): 80A, length: 3,250mm, width: 1,980mm, height: 2,090mm, weight: 8.5t, operating hours: 27,271h, including Spinner SERVO-LOAD 110 1500 bar feeder and documentation. On-site inspection is possible.

więcej

W pełni automatyczna maszyna CNC do nawijania sprężyn skrętnych

Wafios FTU 1.1

Niemcy

1991

używany

na żądanie

INNO32522

Drive: servo motors, individually for each axis, max. number of bending slides: 8, spring steel wire diameter: 0.2-1mm, copper wire diameter: 0.3-2mm, max. winding mandrel diameter: 10mm, max. winding spindle travel: 45mm, max. length of rotating initial leg: 50mm, end leg length: theoretically unlimited, winding spindle revolutions: limited by the winding spindle travel of 45mm, control system: 4-axis CNC positioning control Pronumerik Schleicher, the machine operates using DOS-based programming, including pay-off reel, accessories, operating manuals and documentation, well-maintained and in good condition. On-site inspection is possible.

więcej

Młot pneumatyczny

Reiter Industriewerke Rheinböllen LH 100

Niemcy

1951

używany

na żądanie

INNO32521

Ram weight: 100kg. Including anvil block, anvil, standard dies and motor. Total weight: approx. 3400kg including anvil block. The machine was purchased in working condition in 2019 and has not been operated since. The hammer has very good compression and is in good condition. Low operating hours, no continuous operation. The sliding surfaces of the ram are greased. Documentation available. An on-site inspection is possible.

więcej

Prasa do gięcia krawędzi CNC

Trumpf TrumaBend V130

Niemcy

1991

używany

na żądanie

INNO32516

Offered for sale: Hydraulic CNC press brake with 5-axis backgauge. Bending length: 3060mm. Pressing force: 1300kN, max. stroke: 215mm, max. operating pressure: 340bar, usable installation height: 385mm. Inspection possible by arrangement.

więcej

Piec do wyżarzania

Will Und Hahnenstein EWK-EX

Niemcy

2022

używany

na żądanie

INNO32515

Offered for sale is an electric tempering oven with a maximum operating temperature of 100°C. Approx. dimensions X/Y/Z: 1800mm/1800mm/1600mm. Operation: 2020/2021 in two-shift operation. Inspection possible by arrangement.

więcej

Piec do wyżarzania

Will Und Hahnenstein EWK

Niemcy

2020

używany

na żądanie

INNO32514

Offered for sale is an electric tempering oven with a maximum operating temperature of 250°C. Approx. dimensions X/Y/Z: 3000mm/2200mm/2500mm. Operation: 2020/2021 in two-shift operation. Inspection possible by arrangement.

więcej

Kabina do malowania proszkowego

Durst Lackier- Und Trocknungsanlagen Gmbh GRK 12.000

Niemcy

2020

używany

na żądanie

INNO32513

Offered for sale is a manual powder coating booth with a cartridge filter system. Technical data: Usable volume: 9.5m³, airflow rate: 12000m³/h, downward air velocity: 0.25-0.3m/s, total filter area: 160m², maximum powder melting point: 220°C, maximum dimensions X/Y/Z: 2200mm/200mm/2000mm. Control system: Integrated spray gun and control unit for manual powder coating. Equipment: Booth, platform, filter system, eight cartridges. Operation: 2020/2021 two-shift operation, subsequently approx. 30% daily utilization. System documentation available. Inspection possible by arrangement.

więcej

Pozioma piła taśmowa

Kasto HBA 520/620 AU

Niemcy

1995

używany

na żądanie

INNO32509

Offered for sale is an automatic horizontal bandsaw with roller conveyor. Control system: Electronic machine control system with display, keyboard and control buttons. Equipped with hydraulic workpiece clamping, material feed system, roller conveyor, safety guards and additional bandsaw blades. Inspection possible by arrangement.

więcej

Pionowe centrum obróbcze CNC

Haas VCE 1600W

Niemcy

2000

używany

na żądanie

INNO32508

Offered for sale is a vertical CNC machining center with tool changer. Control system: HAAS CNC control with operator monitor and keyboard. Equipped with automatic tool changer, machine table, enclosed work area, control pendant and tool cart with tool holders. Inspection possible by arrangement.

więcej

Tokarki CNC

Kern CD 322

Niemcy

2007

używany

na żądanie

INNO32507

Offered for sale is a CNC lathe with tool turret. Technical specifications: Machine operating hours: approx. 20000h, main spindle bearings replaced at approx. 16000 machine operating hours. Control system: Heidenhain CNC control. Equipped with tool turret, tailstock, various clamping tools, tool holders, collets and additional tools as well as chip conveyor. Inspection possible by arrangement.

więcej

Piła tarczowa do metalu

Berg & Schmid

Niemcy

nieznany

używany

na żądanie

INNO32498

Offered for sale is a metal-cutting circular saw with a manual clamping system. The machine features a pivoting saw head and a material clamping area with a mechanical clamping device. Equipped with a separate control panel, main switch, emergency stop button, analog indicators and machine stand with integrated storage cabinet. Inspection possible by arrangement.

więcej

Frezarka CNC

Maho MH 500 E2

Niemcy

1990

używany

na żądanie

INNO32497

Travels X/Y/Z: 500mm/400mm/350mm, rotary table diameter: 400mm, spindle taper: SK40, spindle speed: 5000rpm, additional quill travel: 50mm, tool positions: 16, control: Philips 432, machine operating hours: 13400h. Including electronic handwheel and retrofitted LED monitor. The machine was used in single-shift operation. Documentation available. Inspection possible by appointment.

więcej

Pionowe centrum obróbcze CNC

Hardinge Bridgeport XR 1000

Niemcy

2008

używany

na żądanie

INNO32496

Travels X/Y/Z: 1020mm/610mm/610mm, table dimensions X/Y: 1300mm/600mm, max. table load: 900kg, spindle taper: SK40, spindle speed: 12000rpm, tool positions: 30, control: Heidenhain iTNC 530, machine operating hours: 27500h, spindle operating hours: 12700h. Including 3D touch probe, through-spindle coolant at 20bar, additional external air cooling and scraper belt chip conveyor. The machine was used in single-shift operation.

więcej

Liniowa maszyna do nawijania / Linia produkcyjna do produkcji stojanów niQ

Aumann LWS/K 6-160

Niemcy

2016

używany

na żądanie

INNO32494

Aumann LWS/K 6-160 linear winding machine / production system for niQ stators, year of manufacture 2016. Two identical machines are available. Technical data: compressed air connection 5 bar, mains fuse 32 A, rated current 7.2 A, operating voltage 3 x 400 V / N / PE, 50 Hz, control voltage 24 V DC, connected load 5 kVA. Dimensions approx. 1,950 x 1,970 x 2,150 mm (L x W x H). The machines are offered including documentation. An on-site inspection is possible by appointment.

więcej

Wszystkie oferty / Obróbka metali i obrabiarki