▷ Używane maszyny do obróbki metalu z Niemiec | innovac.de

Innovac GmbH Used machines from Germany

Przykład Centrum Obróbcze

Wszystkie oferty / Obróbka metali i obrabiarki / Tokarki

Innovac maszyny-uzywane

Tokarki [1 - 20 of 189]

2-osiowa tokarka CNC

Takisawa EX-122

Niemcy

2008

używany

na żądanie

INNO32357

X-axis: 330mm, Z-axis: 1650mm, max. swing over bed: 910mm, swing over cross slide: 560mm, distance between centers: 1820mm, standard turning diameter: 450mm, max. turning diameter: 610mm, max. turning length: 1650mm, bar capacity: 184mm, spindle speed: 12-1200rpm, spindle nose: A2-15, spindle bore: 200mm, spindle bearing diameter: 266mm, turret type: T10, square tool height: 32mm, boring bar holder diameter: 65mm, tailstock travel: 1400mm, quill stroke: 200mm, tailstock taper: MT5, tailstock quill diameter: 160mm, rapid traverse X-axis: 20m/min, rapid traverse Z-axis: 24m/min, jog feed X-axis: 0-1260mm/min, jog feed Z-axis: 0-1260mm/min, spindle motor power: 30/37kW, X-axis servo motor: 4kW, Z-axis servo motor: 7kW, hydraulic pump: 2.2kW, lubrication pump: 0.004kW, coolant pump: 1.1kW, connected load: 52kW, coolant tank capacity: 300l, hydraulic tank capacity: 83l, lubricating oil tank capacity: 4l, length: 4740mm, width: 2130mm, height: 2090mm, weight: 11t, with documentation. The machine was commissioned in 2008 and operated in single-shift production only, it is currently no longer in operation and has been idle for approx. 2-3 years. An on-site inspection is possible.

Tokarka centralna

Heidenreich & Harbeck M 530

Niemcy

1967

używany

na żądanie

INNO32341

Swing over bed: 540mm, swing over carriage: 280mm, max. cross slide travel: approx. 410mm, max. compound slide travel: approx. 140mm, tailstock quill travel: 225mm, main spindle speed steps: 24, spindle speed: 9-1400rpm, 32 longitudinal feeds: 0.063-2.24mm/rev, 32 cross feeds: 0.032-1.12mm/rev, metric thread pitch: 0.25-560mm, module threads: module 0.1-50, diametral pitch threads: pitch 160-0.5, center height above flat guideway: 265mm, center height above top of V-way: 247mm, bed width: 403mm, main spindle with spindle nose according to DIN 55022: size 11, spindle bore: 103mm, internal taper: 1:20, largest diameter: 109mm, Morse taper of centers: No. 5, leadscrew pitch, standard: 12mm, tailstock quill diameter: 80mm, standard drive power: 18.5kW, rated speed of drive flange motor: 1400rpm, turning tool cross-section according to DIN 770: 25x25mm, max. faceplate diameter: 500mm, max. three-jaw and four-jaw chuck diameter according to DIN 6350: 315mm, weight: 3t, with work light, coolant system with chip tray, four-way tool post with face serration for one-hand operation on the compound slide, operating manual and fixed steady rest. An on-site inspection is possible.

Tokarka

Knuth DL 3000

Niemcy

nieznany

używany

na żądanie

INNO32339

Max. swing over bed: 615mm, max. swing over cross slide: 345mm, distance between centers: 3000mm, spindle bore: 70mm, spindle taper: MT5, forward speed steps: 18, forward speed range: 14-750rpm, reverse speed steps: 9, reverse speed range: 21-857rpm, standard longitudinal feed: 32 steps, 0.1-1.42mm/rev, standard cross feed: 32 steps, 0.03-0.46mm/rev, fine longitudinal feed: 8 steps, 0.048-0.089mm/rev, fine cross feed: 8 steps, 0.015-0.028mm/rev, coarse longitudinal feed: 32 steps, 1.52-2.28mm/rev, coarse cross feed: 32 steps, 0.48-7.2mm/rev, rapid traverse longitudinal: 6m/min, rapid traverse cross: 2m/min, metric threads: 54, range: 1-240mm, Whitworth threads: 37, range: 1-28threads/inch, compound slide travel: 230mm, cross slide travel: 400mm, distance from spindle center to tool holder: 32mm, tool dimensions: 30x30mm, tailstock quill diameter: 100mm, tailstock taper: MT5, quill travel: 205mm, bed width: 490mm, main motor power: 11kW at 1450rpm, rapid traverse motor power: 0.12kW at 1450rpm, coolant motor power: 0.09kW, coolant delivery rate: 25l/min, length: 5500mm, width: 1500mm, height: 1300mm, weight: 4.7t, with documentation. An on-site inspection is possible.

Tokarka CNC

Boehringer VDF 315C

Niemcy

1991

używany

na żądanie

INNO32333

Offered for sale is a robust universal CNC lathe. Turning length: 3000mm, max. torque: 2240Nm, spindle speed range: 16-2500rpm, feed rate: 0.001-9999.999mm/min, rapid traverse rate: 10000mm/min, feed force: 15kN, tailstock quill force: max. 15kN, control: FANUC 15 TF. Equipped with hydraulic tailstock, drum turret, steady rest (range 72-220mm and 28-120mm), various spare parts, defects: machine bed worn, X-axis bearing arrangement makes noise. Weight: approx. 8500kg, overall dimensions X/Y/Z: approx. 6500mm/2200mm/2000mm. Inspection possible by appointment.

Tokarka

Knuth Sinus 400/3000 D

Niemcy

2023

używany

na żądanie

INNO32283

Workpiece length: 3000mm, swing over bed/carriage: 800mm/570mm, turning diameter without gap bridge: 1035mm, gap bridge length: 330mm, bed width: 400mm, travel X/Z: 420mm/230mm, max. spindle speed: 1600rpm, spindle bore: 105mm, spindle mount: D1-8, spindle taper: MT5, tailstock taper: MT5, tailstock quill diameter: 90mm, tailstock quill stroke: 235mm, main drive motor power: 7.5kW. Machine dimensions X/Y/Z: approx. 4740mm/1140mm/1910mm, weight: approx. 3870kg. Including measuring system. Documentation available. An on-site inspection is possible.

Tokarka cykliczna CNC

Wemas HiTurn 550x1500

Niemcy

2008

używany

na żądanie

INNO32273

Distance between centers: 1500mm, swing over bed/cross slide: 620mm/400mm, control: Heidenhain ManualPlus 420. The machine has been in daily single-shift operation since 2008. An on-site inspection is possible.

Tokarka centralna

Gdw LZ 400 VS1 comfortline

Niemcy

2019

używany

na żądanie

INNO32258

Center height: 200mm, distance between centers: 1000mm, swing over bed/cross slide: 400mm/225mm, spindle bore: 62mm, spindle nose: DIN 55027/6, tailstock taper: MK4, max. spindle speed: 4000rpm, main drive power: 10.5kW, operating hours PLC/motor: 1218h/145h. Machine dimensions X/Y/Z: approx. 2100mm/1080mm/1800mm, weight: approx. 1800kg. An on-site inspection is possible.

Tokarka cykliczna CNC

Pinacho Smart Turn 6/225

Niemcy

2008

używany

na żądanie

INNO32238

Center height: 225mm, distance between centers: 1000mm, swing over bed/cross slide: 450mm/260mm, spindle bore: 65mm, max. spindle speed: 3000rpm, max. feed rate: 10m/min, tool turret: 4, main motor power: 7.5kW, control: Fanuc 0i Mate TC. Machine dimensions X/Y/Z: approx. 3500mm/1500mm/1700mm, weight: approx. 1550kg, operating hours: approx. 27000h, feed hours: approx. 1329h. Documentation available. An on-site inspection is possible.

Tokarka CNC

Index ABC 65

Niemcy

2004

używany

na żądanie

INNO32217

An INDEX CNC lathe with counter spindle and IEMCA bar feeder is offered. Main spindle bore: 65mm, max. spindle speed: 7000rpm, axes: 4, live tooling: possible, tool system: VDI25, spindle operating hours: approx. 80000h, control: Siemens 840D. 2) Bar feeder: IEMCA Master 880/MP 33 L, Year of manufacture: 2004, max. bar length: 3300mm, round bars: 8mm-80mm, hexagonal bars: 7mm-65mm, square bars: 10mm-50mm, max. bar weight: 120kg, min. remnant length: 110mm, bar feeder weight: approx. 1350kg. Including chip conveyor. Machine was continuously maintained. The machine is available from October. Documentation available. Inspection possible by arrangement.

Tokarka CNC

Traub TNL 26

Niemcy

2003

używany

na żądanie

INNO32207

Rated current: 60A, control voltage: 24V, connected load: 33kW, length: 2290mm, width: 1350mm, height: 1630mm, weight: 4.65t, operating hours: 78,439h, with documentation, chip conveyor and bar feeder. An on-site inspection is possible.

Tokarka CNC

Traub TNC 42-65

Niemcy

2006

używany

na żądanie

INNO32206

Control voltage: 24V DC, rated current: 85A, connected load: 39kVA, rated power: 49kW, control-on operating hours: 32,779h, automatic operation 1: 5,040h, automatic operation 2 operating hours: 1,844h, production time: 33,731h, length: 3231mm, width: 2076mm, height: 1917mm, weight: 4.8t, with documentation, chip conveyor and FMB turbo 8-80 bar feeder. An on-site inspection is possible.

Tokarka centralna

Wmw DLZ 800/VL x3000

Niemcy

nieznany

używany

na żądanie

INNO32181

Center height: 450mm, distance between centers: 3000mm, fuse protection: 630A, rated current: 46A, control voltage: 220V, operating voltage: 380V, frequency: 50Hz, connected load: 22,5kW, weight: 6,1t, with four-jaw chuck (diameter: 800mm), tailstock, quill and three steady rests. An on-site inspection is possible.

Automat do toczenia długich elementów z wałkiem

Wmw DLZ 1000 III 5000

Niemcy

nieznany

używany

na żądanie

INNO32179

Fuse protection: 100A, control voltage: 220V, operating voltage: 380V, connected load: 30,4kW, weight: 14,4t, with four-jaw chuck (diameter: 900mm), tailstock, quill, three steady rests and control system. An on-site inspection is possible.

Tokarka pionowa

Hessapp VDM1200

Niemcy

2002

używany

na żądanie

INNO32173

Max. turning diameter: 1000mm, max. swing diameter: 1250mm, max. workpiece diameter: 1000mm, max. workpiece length: 850mm, max. workpiece weight: 1000kg, X/Z travel: 1250mm/1000mm, max. speed: 900rpm, feed rate: 14m/min, rapid traverse: 20m/min, spindle nose: DIN 55026 short taper size A15, tool interface: DIN 69880 VDI60 tool holder, spindle diameter at the front bearing: 240mm, control: Siemens Sinumerik 840D. Machine weight: approx. 25t, space requirement: 85m². Equipment: SMW IN-D 1000 chuck, chip conveyor. The machine has no driven tools. Documentation available. Inspection possible by appointment.

Tokarka CNC

Buffalo Machinery Microturn Challenger BNC 1640 S

Niemcy

2007

używany

na żądanie

INNO32165

A Buffalo CNC lathe in need of repair is offered for sale. Center height: 200mm, distance between centers: 880mm, chuck diameter: 160mm, swing over bed: 410mm, swing over cross slide: 230mm, bed width: 260mm, spindle bore: 46mm, spindle nose: A2-5, max. spindle speed: 5000rpm, X-axis travel: 190mm, Z-axis travel: 855mm, rapid traverse: 12m/min, tailstock quill diameter: 58mm, tailstock quill travel: 140mm, tailstock quill taper: MT4, control: Fagor 8055 TC. Accessories included. Dimensions X/Y/Z: approx. 2286mm/1800mm/2230mm, weight: approx. 2350kg. The feed motor of the spindle drive is defective. An on-site inspection is possible.

Tokarka cykliczna CNC

Vdf Boehringer DUS 560

Niemcy

1997

używany

na żądanie

INNO32163

Distance between centers: 2000mm, control: Siemens Sinumerik 810, the control's flash memory is currently probably defective, but the parameters can still be accessed. an on-site inspection is possible.

Kombinowana i pozioma tokarka CNC

Wmz H200-O

Niemcy

2018

używany

na żądanie

INNO32140

Machining processes: drilling, turning, milling, axes: Z3 longitudinal slide tool turret, Z4 longitudinal slide tool turret, X3 cross slide tool turret, X4 cross slide tool turret, C1 workpiece drive, C2 workpiece drive, K5 turret swivel axis, K6 tool drive, K7 turret swivel axis, K8 tool drive, travel X3: 251mm, X4: 251mm, Z3: 662mm, Z4: 662mm, tool turret: 12-station radial, DIN 69880-VDI40, drive: DIN 5480-W20x0.8, tool swing diameter: 580mm, specified dimension at tool area: 320mm, length: 13,000mm, width: 7300mm, height: 4100mm, weight: 22t, operating hours: 14,748h. Equipment: OP012 control panel, Kuka handling robot, chip conveyor, coolant tank, hydraulics, pneumatics, electrical cabinet, parts infeed and outfeed, documentation, installation plan, working area diagram, gearbox plan and transport plan. The following components should be overhauled: machine bed (guideways/ball screws), motor spindles with release units (replace bearings/reseal), cross slides (guideways/ball screws/motor), workpiece spindle (replace bearings/reseal), protective enclosure (interior cladding/working area door/repaint machine), coolant pumps, replacement of electrical cables/lubrication and hydraulic lines, as required. An on-site inspection is possible.

Tokarka CNC z napędem centralnym

Werkzeugmaschinenbau Sinsheim C 704 MV

Niemcy

2000

używany

na żądanie

INNO32138

Workpiece length: 700-2400mm, workpiece diameter: 50-200mm, main spindle drive power: 2x 37kW, max. chuck through-bore: 210mm, chuck piston stroke: 25mm, chuck stroke per jaw: 11.1mm, max. chuck actuating force: 52.5kN, max. chuck actuating pressure: 30bar, max. chuck speed: 2000/min, loading and unloading unit range: 2600mm, center clamping head travel: 1200mm, center clamping head stroke: 1200mm, main fuse: 315A, connected load: 150kW, overall length: approx. 10,640mm, main section length: 6800mm, width: 2370mm, height: 2860mm, overall height including superstructure: 3450mm, operating hours: 3143h. With chip conveyor, loading and unloading unit, fixed center clamping head, movable center clamping head, control panel, ILT air cleaner, electrical cabinet, hydraulic cabinet, coolant tank for motor cooling and coolant tank for tool cooling and documentation. Partially overhauled by the manufacturer in 2021. An on-site inspection is possible.

Tokarka CNC

Optimum OptiTurn L 28HS

Niemcy

nieznany

używany

na żądanie

INNO32137

A CNC lathe Optimum is offered. Swing over bed/cross slide: 300mm/200mm, distance between centers: 430mm, X/Z travel: 145mm/465mm, X/Z rapid traverse: 10m/min/12m/min, bar capacity: 30mm, spindle bore: 30mm, max. spindle speed: 4000rpm, tool stations: 6, control: Siemens SINUMERIK 808D ADVANCED. Machine dimensions X/Y/Z: approx. 1655mm/1590mm/1955mm, weight: approx. 832kg. An on-site inspection is possible.

Tokarka CNC z napędem centralnym

Werkzeugmaschinenbau Sinsheim CM 704

Niemcy

2003

używany

na żądanie

INNO32135

Cross slide NC1-left, X1-axis: 450mm, cross slide NC1-left, Z1-axis: 1980mm, cross slide NC2-right, X2-axis: 450mm, cross slide NC2-right, Z2-axis: 1980mm, M-head slide-left, Q1-axis: 1980mm, M-head slide-right, Q2-axis: 1980mm, tailstock + steady rest slide-left, W1-axis: 1980mm, tailstock + steady rest slide-right, W2-axis: 1980mm, Y-axis: +/-65mm, workpiece length: 760-3000mm, workpiece clamping diameter: 20-200mm, main drive power: 2x 37kW, main drive speed (stepless): 0-2200/min, tool drive speed (stepless): 0-2320/min, tool holder: VDI50, tailstock center: MK 5, number of tool holders: 12, steady rest: SLU-5 SO, steady rest clamping diameter: 20-200mm, working height: 1300mm, max. workpiece diameter: 20-200mm, max. workpiece weight: 250kg, workpiece drive/clamping: 2x hydraulically operated SAV front-end chucks, max. chuck through-bore diameter: 210mm, spindle power: 2x 37kW, max. rapid traverse speed: 20m/min, control: Siemens 840D SL, connected load: 135kW, length: 7800mm, width: 3000mm, height: 3250mm, weight: 42t, with machine documentation, installation plan, foundation plan, transport plan, Knoll coolant system, Knoll chip conveyor, ILT extraction system and Promot loading and unloading gantry. Regularly serviced by the manufacturer, the machine was completely overhauled by the manufacturer in 2016. An on-site inspection is possible.