Podwójna piła ukosowa

Emmegi Norma 2-400 TU/4

Niemcy

2020

używany

na żądanie

INNO29058

Saw blade diameter: 2x400mm, max. cutting length: 4000mm, cutting angle: +/-45°. Documentation available. On-site inspection is possible.

więcej

System spawania dźwigarów kratowych

Ideal GA 400/1600

Niemcy

1988

używany

na żądanie

INNO29055

A steel mesh welding system for the automatic production of welded steel wire mesh is available. Mesh width range: 250mm-1600mm, mesh length range: 600mm-2900mm, min. cross wire pitch: 15mm, min. longitudinal wire pitch: 25mm, increments of longitudinal wire pitch: 5mm, wire diameter range: 3mm-8mm, number of longitudinal wires: 20, number of welding presses: 12, rated power at 50%: 6x130kVA. On-site inspection is possible.

więcej

System spawania dźwigarów kratowych

Evg LGR/85-PV

Niemcy

2001

używany

na żądanie

INNO29054

A steel mesh welding system for the automatic production of welded steel wire mesh is available. Mesh width range with a bar diameter of 3mm to 6mm: 500mm-2150mm, mesh width range with a bar diameter of 2mm to 3mm: 500mm-2000mm. Grid length range with a rod diameter of 3mm to 6mm: 600mm-3000mm, grid length range with a rod diameter of 2mm to 3mm: 600mm-2000mm. Min. cross wire pitch: 12.5mm, min. longitudinal wire pitch: 25mm, wire diameter range: 2mm-6mm, max. number of longitudinal wires: 52, production capacity: 52 strokes/min, rated power at 50%: 840kVA, max. stack height: 600mm. Total system dimensions X/Y/Z: approx. 20000mm/7600mm/3400mm. Including longitudinal wire distributor in 40mm and 50mm pitch and longitudinal wire console in 40mm, 50mm and 75mm pitch. Documentation available. On-site inspection is possible.

więcej

System spawania dźwigarów kratowych

Filzmoser GH400V-ST

Niemcy

2009

używany

na żądanie

INNO29053

A fully automatic lattice girder welding system for the production of reinforcing steel (rebar) is available. Outlet height: 1400mm, beam length min./max.: 800mm/16000mm, base width: 58mm, beam width range: 70mm-116mm, max. production capacity: 15m/min. Beam type KT: upper beam diameter range: 5mm-16mm, lower beam diameter range: 5mm-16mm, diagonal beam diameter range: 4.5mm-9mm, beam height range: 70mm-400mm, diagonal pitch: 190mm-210mm. Beam type KTS: top chord diameter range: 5mm-7mm, bottom chord diameter range: 5mm-7mm, diagonal beam diameter range: 5mm-7mm, beam height range: 80mm-310mm, diagonal spacing: 200mm. Documentation available. On-site inspection is possible.

więcej

Spawarka doczołowa

Strecker SS 120 FPC

Niemcy

2011

używany

na żądanie

INNO29052

Eine Strecker Widerstandsstumpfschweißmaschine mit integrierter hydraulischer Presseinheit ist verfügbar. Nennleistung bei 50%: 120kVA, Nennstrom: 300A, Betriebsdruck: 350bar, max. Spannkraft: 69kN, max: 44kN, Hydraulikaggregat: K-VDS-700, Schneidleistung: 32mm, Kolbenpresskraft: 44t, schwenkbar: möglich. Maschinenabmessungen X/Y/Z: ca. 1800mm/1100mm/1600mm, Gewicht: ca. 2300kg, Steuerung: VIPA S7. Dokumentation vorhanden. Besichtigung vor Ort ist möglich.

więcej

Maszyna do cięcia laserowego CNC

Amada FLC-3015 AJ-2000

Niemcy

2017

używany

na żądanie

INNO29039

A comprehensive Amada CNC laser cutting system is available. Travel X/Y/Z: 3070mm/1550mm/100mm, max. table load: 920kg, positioning speed: 120m/min, simultaneous speed: 169m/min, acceleration: 30m/s², positioning accuracy: +/-0.01mm, position spread: +/-0.005mm, cutting capacity mild steel/aluminum/brass/copper: 16mm/10mm/8mm/5mm/4mm, machine weight: approx. 11000kg, control: AMNC 3i. Laser source: fiber laser, laser power: 2000W, wavelength: approx. 1µm, nozzle positions: 8, cooling system: WACS, conveyor belt direction: X. Including loading and unloading Profibus, water desalinator, water recooler, pallet changer and extraction system. Documentation available. On-site inspection is possible.

więcej

System EDM

Zimmer & Kreim ZK Genius 700/Chameleon Quad

Niemcy

2019

używany

na żądanie

INNO29038

An eroding island consisting of two die-sinking EDM machines and an automation system is available. 1) Zimmer & Kreim ZK Genius 700, year of manufacture: 2015, travel X/Y/Z: 400mm/350mm/350mm, table dimensions X/Y: 575mm/500mm, max. workpiece weight: 700kg, generator output: 96A, path eroding: CIMCO, operating hours: 22056h. 2) Zimmer & Kreim ZK Genius 700, year of manufacture: 2019, travel X/Y/Z: 400mm/350mm/350mm, table dimensions X/Y: 575mm/500mm, max. workpiece weight: 700kg, generator power: 96A, path eroding: CIMCO, operating hours: 8255h. 3) Automation Zimmer & Kreim Chameleon Quad, year of construction: 2015, electrode positions: 176, pallet positions with loading drawer: 9, double rotary gripper for Erowa ITS and single gripper for UPC pallets. Overall system dimensions X/Y: approx. 3000mm/6200mm. Including a Kraft & Bauer fire extinguishing system with suction device. Documentation available. On-site inspection is possible.

więcej

Maszyna do zwijania sprężyn

Wafios FTU 3.3

Niemcy

1996

używany

na żądanie

INNO29037

A Wafios CNC spring coiling machine is available. Wire diameter range: 1.5mm-6mm, max. spring diameter: 20mm, feed rate: 40m/min, production output: 80 pieces/min, axis resolution X/Y/Z/C/A/O: 0.1°/0.36°/0.001mm/0.001mm/0.1°/0.1°, working height: 1200mm, machine dimensions X/Y/Z: approx. 2300mm/2500mm/2400mm, control: Schleicher. On-site inspection is possible.

więcej

Szlifierka

Lissmac Steelmaster SMD 134 RRT

Niemcy

2017

używany

na żądanie

INNO29036

A Lissmac grinding and deburring machine is available. Working width: 1100mm, material thickness range: 0.5mm-160mm, feed speed range: 2500mm-13000mm, rated power: 32kW, weight: approx. 2300kg. Documentation available. On-site inspection is possible.

więcej

Pionowe centrum obróbcze

Buffalo Machinery Micromill Challenger MM-430

Niemcy

2011

używany

na żądanie

INNO29033

X-axis: 300mm, y-axis: 620mm, z-axis: 400mm, positioning accuracy: ±0.005 inch, repetition accuracy: 0.005 inch, rapid traverse: 25m/min, feed rate: 10m/min, air pressure: 6kg/cm², air consumption: 400l, pump motor: 30W, delivery rate: 2.2cm³/s, pump pressure: 8kg/cm², tank capacity: 2l, pump electrics: 220V/ 3PH/ 1.2A, max. delivery rate: 130l/min, control: Heidenhain TNC 620, connected load: 15kVA, length: 3000mm, width: 2050mm, height: 3020mm, weight: 3020kg. max. flow rate: 130l/min, control: Heidenhain TNC 620, connected load: 15kVA, length: 2984mm, width: 2050mm, height: 2420mm, weight: 3020kg. Operating hours control: 22,261h, machine: 22,414h, programme: 10,507h, spindle: 7695h. Fully functional, spindle was recently replaced, the built-in oil skimmer in the cooling water tank is not functional. With documentation. On-site inspection is possible.

więcej

Cela spawalnicza robota

Igm RTE 497-S

Niemcy

2021

używany

na żądanie

INNO29032

Robot travel path: 5000mm, arm length: 2500mm, lift: 1000mm, spin radius: 2200mm, L-manipulator load capacity: 2000kg, lift velocity: 0,85m/min, swing speed: 1,7/min, turn speed: 6/min. Roboter type: IGM RTE 497-S in hanging position, control: full digital PC-Robotcontrol, Type RCE, software: WIN 10 & Linux based System + igm Robotsoftware K6, welding process: 135 (GMAW), single-wire, Ø1,2mm, welding power source: digital Invert Welding Power Source TPS 500i (500A at 40% duty cycle), robot periphery: rotating boom for floor installation with 2,5m boom length, number of working stations: 1, working station: 3-axis L-Manipulator with lifting device with 2t nominal load capacity, security Technology: Pistol-Security-Shut-down in wrist axis, emergency Stop on Handtablet, on Manipulators and Control Panel, three-coloured warning light for the operating Status partition, security Door. machine is complete, no defects known, documentation complete, was maintained regularly. An on-site inspection is possible.

więcej

Hydrauliczna prasa krawędziowa

Gwf H 100-2

Niemcy

1992

używany

na żądanie

INNO26811

Compressive force: 1000kN/100t, ram stroke: 200mm, max. operating pressure: 290bar, control: DNC70, safety distance: 166mm, overtravel time: 104ms, overtravel distance: 7mm.

więcej

Maszyna wykrawająca

Trumpf TRUMATIC 500

Niemcy

2000

używany

na żądanie

INNO29030

Working range X/Y: 2500mm/1300mm, max. workpiece weight: 150kg, stroke rate: 900 strokes/min, max. sheet thickness: 8mm, max. punching force: 220kN, max. Punching diameter: 76.2mm, speed X/Y/simultaneous: 90m/60m/108m/min, C-axis: 360°/s, positioning accuracy: +/-0.1mm, position spread: +/-0.03mm, tool positions: 20. Machine dimensions X/Y/Z: approx. 6900mm/5800mm/2200mm, weight: approx. 11000kg, control: Trumagraph CC 220 S. The machine is not functional. Documentation available. On-site inspection is possible.

więcej

Maszyna Flakkotier

Profin BLUELINE HFM 1/2-R

Niemcy

2010

używany

na żądanie

INNO23597

Suitable for edge preparation of all types of cutting tools with the corresponding holders and turning devices, e.g. roll cutters turning devices, e.g. cylindrical milling cutters, saw blades up to 380mm diameter, shank tools, indexable inserts and saw band coils up to 750mm diameter. Number of units: 1, table pitch circle: 600mm, table outer diameter: 800mm, machining width/height: 180/ 250mm, feed rate: 0.5-6m/min, flakkotier power: 4kW, connected load: 6.4kW, length: 2500mm, width: 1950mm, height: 2500mm, weight: 3t, operational hours counter: approx. 100h. Including documentation, without accessories or spare parts. On-site inspection is possible.

więcej

Magazyn do podajnika barów

Kurt Breuning Irco SIMAG 80.1 U/3000-II

Niemcy

2022

używany

na żądanie

INNO29023

Guide channel sets for diameters: 22, 42, 47, 52, 62, 67, connected load: 2.4 kVA, weight: 1.8 tonnes. Featuring short changeover times, easy handling, maximum running smoothness, hydrodynamic bearings, 360° closed guide channels, reliable feeding of rotationally symmetrical profile material. The machine has only been used a little, an on-site inspection is possible.

więcej

Nożyce gilotynowe

Durmazlar DHGM 4006

Niemcy

1996

używany

na żądanie

INNO29021

Working width: 41100mm, max. sheet thickness: 6mm, stroke: 131mm, stroke rate: 12/min, max. pressure: 150bar, oil tank capacity: 250l, control: ELGO Electric, motor power: 18.5kW, length: 4750mm, width: 2350mm, height: 1950mm, weight: 12t. On-site inspection is possible.

więcej

Szlifierka CNC do boków zębów

Bhs-hoefler SUPRA 1603

Niemcy

1989

używany

na żądanie

INNO26321

Max. table load: 8t, diameter table: 2000m, max. wheel diameter wheel: 720mm, pressure angle: 12.5-30°, max. bevel angle: 35°, diameter grinding wheel: 300mm/400m, peripheral speeds: 25 or 35m/s, grinding stroke: 750mm, number of teeth: 12-372, length: 6800mm, width: 5500mm, height: 3800mm, weight: 26t, was modernized in 2000 and equipped with CNC control, with documentation, on-site inspection is possible.

więcej

Dwukolumnowa prasa do rysowania

Müller ZE 250/315

Niemcy

1978

używany

na żądanie

INNO29016

Pressing force: 3150kN, table dimensions: 1250x1100mm, table height: 750mm. Fully functional, last internal inspection: Q1/2025, UVV on Q2/2024. On-site inspection is possible.

więcej

Jednokolumnowa prasa ekscentryczna

Müller Weingarten AR 100W

Niemcy

1969

używany

na żądanie

INNO29015

Press force cutting and drawing ram: 1000kN, table dimensions: 710x560mm, thickness of clamping plate: 90mm. Fully functional, last internal inspection: Q1/2025, UVV on Q2/2024. On-site inspection is possible.

więcej

Centrum toczenia i frezowania CNC

Niles-simmons N30/2500 MC

Niemcy

2002

używany

na żądanie

INNO29009

With two machining modules, X-axis: -50 to 725mm, Y-axis: -200 to 300/ -250 to 250mm, rapid traverse X-, Y-, Z-axis: 18/12/30m/min, turning lengths: 1500/2000/2500/3200/4000/4500/6500mm, swing diameter: 780/ 880mm, turning spindle bore: 92/123mm, main spindle speed range: 0-3000/0-3000/2000/min, max. Turning/milling unit speed: 5000/6000/10000/min, max. tool length: 900/600/1000/300/900mm, quill stroke: 160/170mm, connected load: 102kVA, control system: SINUMERIK ONE / SINUMERIK 840D sl, drive system control: SINAMICS S120, weight: 17t. On-site inspection is possible.

więcej

Wszystkie oferty / Obróbka metali i obrabiarki