Offered is an Extruder AF 2 V Alimentazione Forzata with double degassing. Screw diameter: approx. 160mm, D ratio: approx. 37, DC drive, ABB rectifier DCS 500 visible, control: Siemens S5/S7, pelletizing: hot face/water ring, hydraulic unit: available, frequency inverter: Control Techniques / Emerson. Known defects: silo shortened/holes, vertical screw circuit missing, pelletizing shaft disassembled, screen changer frame warped. Inspection possible by appointment.
A complete PS foam extrusion line (capacity: 350kg-400kg/h) is available. 1) 7x dosing units K-Tron Switzerland and Coperion, main components: 3, side components: 4, capacity: 350kg-400kg/h. 2) Primary extruder Battenfeld, year of manufacture: 1998, screw diameter: 120mm, screen changer: Gneuss, double piston pump: LEWA. Including gas injection. 3) Secondary extruder, screw diameter: 150mm/33D. Including unused old die and a coextruder Kühne with 50mm screw diameter. 4) Oil-heated Sunwell round die. 5) Calibration unit Dorn, knives: 2, films: 2, film width: 1080mm. 6) Take-off unit Gloenco Double S Haul-Off. 7) PS film winder, positions: 4, simultaneously operated positions: 2, winding speed range: 10m-30m/min, roll weight range: 150kg-300kg, roll length range: 500mm-800mm. Including discharge with ionization. Documentation available. An on-site inspection is possible. This line is sold ONLY to customers outside Europe.
One complete and one partially dismantled extruder system Davis are available. 1) Davis Standard DS-25, power: 6385W, max. melt pressure: 700bar, max. temperature: 315°C. Including 4x screws, 6x bursting discs, Digicolor dryer, platform, screen changer with heating and sealing pack, new cylinder, 3x screw seals, and spare drive motor. 2) Davis Standard DS-20, power: 4500W, max. operating pressure: 700kg/cm², max. temperature: 315°C. Including Conair dryer, 3x screws, screen changer with heating and sealing pack, cast housing, extrusion tool, and spare drive motor. General accessories: various ring heaters, 3x Eurotherm temperature controllers, and 3x Eurotherm pressure sensors. Documentation available. An on-site inspection is possible.
A complete extrusion line with a Reifenhäuser extruder and a gravimetric system Plast-Control (2006) is available. 1) Unwinder 1. 2) Primer unit and hotmelt unit for water-based adhesive lamination. 3) Dryer. 4) Unwinder 2. 5) Dolci extruder for extrusion lamination. 6) Unwinder 3. 7) Two printing units with additional dryer. 8) Extruder Reifenhäuser. 9) Rewinder. 10) Guide roller in the basement. 11) Web guiding under unwinder 1 in the basement. 12) 2x resin silos in the basement. This is a complete extrusion line with peripheral equipment. Documentation available. An on-site inspection is possible.
Two gravimetric Colotronic batch dosing and mixing machines with a main extruder and a co-extruder are available. 1) Colortronic UB 675, year of manufacture: 2010, max. throughput: 700kg/h, mixing components: 6, dosing principle: vertical slide gate. 2) Colortronic UB 975, year of manufacture: 2010, max. throughput: 2500kg/h, components: 2-8. Dosing and mixing capacity (both together): approx. 230kg/h. Documentation available. On-site inspection is possible.
Control panel: Siemens SIMATIC HMI, connected load: 80kW, weight: 1.85t, operating hours: approx. 4500h, with Kreyenborg feed hopper, year of manufacture: 2017, and Trendelkamp screen changer. Documentation is complete, on-site inspection is possible.
A complete Artec recycling and extrusion line is available. Material: PE/PP/PS/ABS/LDPE/HDPE/MDPE, screw diameter: 145mm, L/D ratio: 42, extrusion capacity: 700kg/h, degassing: 2-fold, shredder/extruder/screen changer output: 55kW/609kW/55kW. Total plant dimensions X/Y/Z: approx. 20700mm/3000mm/3400mm, control system: Siemens. Including shredder, conveying units, storage and mixing silo, feed belt, extruder, vacuum pump, melt filter, hot granulating cut-off, bag filling and weighing station and bagging station. Documentation available. On-site inspection is possible.
A complete Artec recycling and extrusion line is available. Material: PE/PP/PS/ABS/LDPE/HDPE/MDPE, screw diameter: 125mm, L/D ratio: 42, extrusion capacity: 650kg/h, degassing: 2-fold, shredder/extruder/screen changer output: 55kW/512kW/55kW. Total plant dimensions X/Y/Z: approx. 20700mm/3000mm/3400mm, control system: Siemens. Including shredder, conveying units, storage and mixing silo, feed belt, extruder, vacuum pump, melt filter, hot granulating cut-off, bag filling and weighing station and bagging station. Documentation available. On-site inspection is possible. The system has extensively documented defects.
Screw diameter: 59mm, screw rotational speed: 25-250/min, with complete documentation, control cabinet, screen changer, side dosing unit, granulator and additional accessories.
Extruder and extrusion lines [1 - 15 of 15]
de-DE
pl-PL
