▷ Used plastics processing machines from Germany | innovac.de

Innovac GmbH Used machines from Germany

i.e. Machining Center MORI SEIKI

Innovac used-machines

Injection moulding machinery [1 - 20 of 89]

Injection Moulding Machine

Wittmann Battenfeld SmartPower 90/130 UNILOG B8

Germany

2018

used

on request

INNO32461

Clamping force: 900kN, screw diameter: 30mm, L/D ratio: 22, specific injection pressure: 1540bar, calculated shot volume: 88.4cm³, max. shot weight (PS): 80.4g, tie-bar spacing (H×V): 470mm/420mm, min. mold height: 225mm, max. platen distance: 700mm, opening stroke: 475mm, ejector stroke: 150mm, ejector force: 41.2kN, control system: UNILOG B8, weight: 4200kg. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Klöckner Desma D 969.250 Z (S3)

Germany

2021

used

on request

INNO32431

Clamping force: 2700kN, injection volume: 500cm³, injection pressure: 3500bar, EUROMAP size: 2700-1750, rated power: 22kW, weight: approx. 10.7t, nozzle contact force: 58kN, total current: 138A, upstream fuse: 160A, max. short-circuit current: 10kA, enclosure type (UL): 1, hydraulic motor operating hours: 730h, hydraulic pump (clamping force): 65h, operating system active: 3,360h, was regularly maintained, is in well-maintained condition, an on-site inspection is possible.

Injection Moulding Machine

Demag Ergotech Krauss Maffei extra 80-430

Germany

unknown

used

on request

INNO32401

Clamping force: 800kN, tie-bar spacing: 400mm, injection unit: 430, max. flow rate: 76l/min, max. hydraulic pressure: 210bar, control: CDIAS, weight: 3.6t, an on-site inspection is possible.

Injection Moulding Machine

Sumitomo Demag IntElect 100/470-340

Germany

2014

used

on request

INNO32400

Clamping force: 100kN, tie-bar spacing: 470mm, mains connection: 400V/50Hz/64A, control: CDIAS, weight: 5.7t, an on-site inspection is possible.

Vertical Injection Moulding Machine

Cronoplast BABYPLAST 6/10VP

Germany

2009

used

on request

INNO32395

Mains voltage: 400V, 3L+N, 230V, 3L, rated current: 7.5A at 400V, 11A at 230V, frequency: 50/60Hz, short-circuit breaking capacity: 3.5kA, weight: 370kg, an on-site inspection is possible.

Injection Moulding Machine

Krauss Maffei KM 80-220 C2

Germany

1999

used

on request

INNO32381

Clamping force: 80t, 3-phase mains supply: 400V, 50Hz, total rated current: 130A, upstream fuse: 160A, max. motor current: 30A, an on-site inspection is possible. The machine is located in Hungary.

Injection Moulding Machine

Krauss Maffei KM 350-1400-390 CZ

Germany

2005

used

on request

INNO32352

Max. locking force: 3500kN, clear tie-bar spacing: 710x710mm, min. mold height: 380mm, max. opening stroke: 1300mm minus mold height, max. ejector stroke: 250mm, max. ejector force: 95kN, ejector retraction force: 48kN, rotary table diameter: 890mm, screw diameter K1: 60mm, K2: 35mm, nozzle radius: 15mm, max. injection pressure K1: 2000bar, K2: 2429bar, max. shot weight (PS) K1: 618g, K2: 142g, hot runner: external, core pull connection: DNP Flatface BG3 (large flat-face sealing), centering mandrel: AS + DS, weight: 16.37t, total operating hours: 74,276h, production hours: 66,341h, the second injection unit and the rotary table have not been used for five years, with documentation and linear handling system, regularly maintained in-house. An on-site inspection is possible, the machine is not connected to power.

Injection Moulding Machine

Mannesmann Demag D 650-4500

Germany

1995

used

on request

INNO32348

Clamping force: 6500kN, locking force: 7150kN, max. opening stroke: 930mm, mold height: 360-920mm, max. distance between mold mounting platens: 1850mm, mold mounting platens: 1350x1350mm, clear tie-bar spacing: 900x900mm, max. mold weight: 8.6t, max. weight on moving mold mounting platen: 5.7t, screw diameter: 110mm, L/D ratio: 17.2, injection pressure: 1270bar, shot volume: 3570cm³, shot weight (PS): 3180g, max. metering stroke: 375mm, max. nozzle stroke: 850mm, nozzle immersion depth (SVO): 70mm, nozzle contact force: 200kN, installed barrel heating capacity: 52kW, hopper capacity: 110l, the machine screw is defective. With documentation. An on-site inspection is possible.

Injection Moulding Machine

Krauss Maffei Extra 100-430

Germany

2006

used

on request

INNO32321

Clamping force: 800kN, an on-site inspection is possible.

Injection Moulding Machine

Arburg ALLROUNDER CENTEX 470C 1500-350/150

Germany

2005

used

on request

INNO32310

Clamping force: 1500kN, rated current: 133A, connected load: 74kW, an on-site inspection is possible.

Injection Moulding Machine

Krauss Maffei KM 65-380 CX

Germany

2008

used

on request

INNO32309

Clamping force: 650kN, length: 4000mm, width: 1600mm, height: 2200mm, weight: 3.9t, an on-site inspection is possible.

Injection Moulding Machine

Krauss Maffei KM 160-1000 CX

Germany

2005

used

on request

INNO32308

Clamping force: 1600kN, width: 1600mm, height: 2200mm, weight: 6.8t, an on-site inspection is possible.

Injection Moulding Machine

Demag Ergotech 1250-440 concept

Germany

2001

used

on request

INNO32307

Clamping force: 1250kN, tie-bar spacing: 475x450mm, injection unit: 440, max. flow rate: 100l/min, max. hydraulic pressure: 190bar, weight: 6.6t, an on-site inspection is possible.

Injection Moulding Machine

Demag Ergotech Extra 80-430

Germany

2004

used

on request

INNO32306

Clamping force: 800kN, tie-bar spacing: 400mm, injection unit: 430, max. flow rate: 76l/min, max. hydraulic pressure: 210bar, control: CDIAS, weight: 3.6t, an on-site inspection is possible.

Thermoplastic Injection Moulding Machine

Polyapress

Germany

unknown

used

on request

INNO32260

Condition: used, with visible signs of use, was operational until placed in storage, control voltage: 24V, operating voltage: 230V, frequency: 50Hz, CO₂ pressure: 10bar, connected load: 500W, with CE marking. An on-site inspection is possible.

Injection Moulding Machine

Battenfeld TM 4500/3300

Germany

2004

used

on request

INNO32239

A BATTENFELD large-format horizontal injection molding machine in need of repair is offered. Operating pressure: 210bar, clamping force: 4500kN, screw diameter: 85mm, injection volume: 2128cm³, injection pressure: 1624bar, tie-bar spacing X/Y: 900mm/800mm, opening stroke: 950mm, max. mold height: 970mm, oil capacity: 900l, connected load: 55kW, operating hours: approx. 82510h, weight: approx. 20.4t. The servo motor for the screw drive is defective. In addition, some smaller parts are missing. An on-site inspection is possible.

Injection Moulding Machine

Arburg 320C 500-170 Golden Edition

Germany

2006

used

on request

INNO32196

Clamping force: 500kN, tie-bar spacing: 320x320mm, cylinder diameter: D30, control: Arburg SLOGICA, automatic operating hours: 63.147h, pump operating hours: 65.755h, semi-automatic operating hours: 14h, cycles: 13.943.435. An on-site inspection is possible.

Injection Moulding Machine

Arburg ALLROUNDER 270C 300-100 control+

Germany

2003

used

on request

INNO32195

Clamping force: 300kN, tie-bar spacing: 270x270mm, cylinder diameter: D15, control: Arburg Control+, automatic operating hours: 63.212h, pump operating hours: 63.212h, cycles: 15.328.195. An on-site inspection is possible.

Injection Moulding Machine

Engel Victory 1050/180 tech

Germany

2014

used

on request

INNO32166

Clamping force: 1800kN, opening force: 96kN, max. opening stroke: 750mm, min. mold height: 300mm, max. platen distance: 1050mm, clear tie-bar spacing: tie-bar-less, mold mounting platens X/Y: 880mm/830mm, max. mold weight: 1500kg at center of gravity 230mm, ejector stroke: 180mm, ejector force forward/backward: 80kN/33kN, screw diameter: 55mm, metering stroke: 215mm, max. stroke volume: 510cm³, injection rate: 255cm³/s, max. injection pressure: 2050bar, nozzle stroke: 350mm, nozzle contact force: 67kN, injection unit heating capacity: 16.3kW, heating zones incl. nozzle: 5, barrel: M9 bimetallic barrel, integrated hot runner control zones: 24×220V, mold cooling circuits: 6×10l/min, hydraulic oil capacity: approx. 540l, operating hours: 67423h (as of 30.06.2026). The machine will be available from December. Machine dimensions X/Y/Z: approx. 6275mm/1888mm/2100mm, weight without mold: approx. 12200kg. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Engel e-victory 440/180

Germany

2017

used

on request

INNO32156

Clamping force: 1800kN, max. opening stroke: 750mm, min. mold installation height: 300mm, screw diameter: 40mm, L/D: 20, G4 S10, clear tie-bar spacing: tie-barless, max. stroke volume: 220cm³, injection rate: 223cm³/s, max. injection pressure: 1930bar, material barrel: M9 (bimetallic barrel), length: 6455mm, height: 2100mm, weight without mold: 13.7t, operating hours: 59,947h, with documentation. Available from December 2026, an on-site inspection is possible.