▷ Used plastics processing machines from Germany | innovac.de

Innovac GmbH Used machines from Germany

i.e. Machining Center MORI SEIKI

Innovac used-machines

Injection moulding machinery [21 - 40 of 89]

Injection Moulding Machine

Arburg 375V 500-100

Germany

2008

used

on request

INNO32126

A vertical injection moulding machine from ARBURG is offered. Clamping force: 50t, table size X/Y: 500mm/420mm, max. shot volume: 65cm³, min. opening width: 272mm (172mm), max. opening width: 522mm (422mm), hydraulic/pneumatic cascades: 2/4, hydraulic/pneumatic core pulls: 0/0, hydraulic operating hours: 6979h, automatic operating hours: 4696h, total cycles: 142609. Including shuttle table. Documentation available. Inspection possible by arrangement.

Injection Moulding Machine

Krauss Maffei KM 550/ 3000 GX 550

Germany

unknown

used

on request

INNO32101

The injection momlding machine corresponds to the hydromechanical two-platen series, clamping force: 550t, operating hours: approx. 80h, with Handling Krauss Maffei KM 250/ LRX-S 250. An on-site inspection is possible, the machine is located in Mexico.

Injection Moulding Machine

Krauss Maffei KM650/3000CX

Germany

2010

used

on request

INNO32068

A fully hydraulic large-format two-platen injection molding machine from Krauss Maffei with an LRX350 linear robot is available. Clamping force: 6500kN, injection unit: SP3000, screw diameter: 70mm, L/D ratio: 22.9, max. injection pressure: 2389bar, shot volume: 1232cm³, shot weight: 1121g, injection rate: 462cm³/s, screw speed: 285rpm, plasticizing rate: 108.6g/s, nozzle contact force: 129kN, mold opening force: 345kN, mold opening stroke: 1150mm, min. mold height: 600mm, max. daylight opening: 1750mm, ejector stroke: 250mm, ejector force: 95kN, max. mold weight: 11400kg, clear distance: 1200mm/1120mm, platen dimensions X/Y: 1510mm/1370mm. Robot payload: 35kg, travel X/Y/Z: 1200mm/2000mm/4000mm, conveyor dimensions X/Y: 2500mm/800mm, discharge height: 1000mm, max. conveyor belt temperature: 70°C. Machine dimensions X/Y/Z: approx. 8000mm/3000mm/2700mm, weight: approx. 31t, operating hours: approx. 75900h. Documentation available. An on-site inspection is possible. Available from approximately November 2026.

Injection Moulding Machine

Arburg Allrounder 570 A 2000-800

Germany

2010

used

on request

INNO32019

Three similar Arburg injection molding machines are available. 1) Arburg ALLROUNDER 570 A 2000-800, year of manufacture: 2010, clamping force: 2000kN, distance between tie bars: 570mm/570mm, pressure: 575bar, control system: Selogica direct 4.090, operating hours: 91917h, weight: approx. 9800kg. 2) Arburg ALLROUNDER 570 A 2000-800, year of manufacture: 2011, clamping force: 2000kN, distance between tie bars: 570mm/570mm, pressure: 575bar, control system: Selogica direct 4.090, operating hours: 82736h, weight: approx. 9800kg. 3) Arburg ALLROUNDER 570 A 2000-800, year of manufacture: 2011, clamping force: 2000kN, distance between tie bars: 570mm/570mm, pressure: 575bar, control system: Selogica direct 4.090, operating hours: 90722h, weight: approx. 9800kg. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Battenfeld BK-T 1000/400

Germany

1994

used

on request

INNO31953

A hydraulic Battenfeld plastic injection molding machine is offered. Clamping force: 1000kN, screw diameter: 40mm, shot weight: approx. 183g, mold mounting platens X/Y: 700mm/700mm, shot volume: 201cm³, max. injection pressure: 1968bar, max. screw speed: 290rpm, nozzle contact force: 79.2kN, machine cycles: approx. 1985087, operating hours: approx. 53578h, control system: Battenfeld UNILOG 4000. Dimensions: approx. 5440mm/1550mm/2300mm, weight: approx. 5060kg. Motor, pump and inverter renewed in December 2009. An on-site inspection is possible.

Injection Moulding Machine

Arburg Allrounder 375 V 500-170

Germany

2011

used

on request

INNO31680

A virtually new and almost fully equipped Arburg vertical injection molding machine from a laboratory is available, where its plasticizing unit was never used. Clamping force: 500kN, opening force: 30kN, opening stroke: 250mm, ejector force: 30kN, ejector stroke: 70mm, screw diameter: 25mm/30mm/35mm, nozzle contact force: 50kN, nozzle retraction stroke: 210mm, heating capacity: 9kW, heating zones: 5, hopper volume: 25l, technology level: T2, rotary table diameter: 900mm. Machine dimensions X/Y/Z: approx. 3400mm/2050mm/3500mm, weight: approx. 4200kg, operating hours: 9201h, machine cycles: approx. 120k. The machine was used exclusively for composite materials such as carbon fiber and Kevlar. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Krauss Maffei 650-5700 CM

Germany

1999

used

on request

INNO31654

A large-format injection molding machine Krauss Maffei is available. Clamping force: 6500kN, tie bar spacing X/Y: 1000mm/930mm, platen dimensions X/Y: 1530mm/1450mm, max. opening stroke: 900mm, mold height range: 350mm-650mm, max. platen spacing: 1550mm, ejector stroke: 250mm, ejector force: 110kN. Machine dimensions X/Y/Z: approx. 10000mm/2800mm/2450mm, weight: approx. 46000kg. Including a Wittmann handling unit. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Krauss Maffei KM300-1900 C2

Germany

2000

used

on request

INNO31642

Clamping force: 3000kN, stroke volume: 1047cm³, shot weight: 953g, injection pressure: 1778bar, screw diameter: 70mm, tie-bar spacing: 630mm, opening stroke: 1150mm, ejector stroke: 200mm, installation height: 330mm, platen width: 1050mm, platen height: 995mm. Machine dimensions X/Y/Z: approx. 6250mm/2050mm/2400mm, weight: approx. 12500kg. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Battenfeld HM 1600/1000

Germany

2002

used

on request

INNO31503

Clamping force: 1600kN, tie bar spacing: 570x520mm, platen dimensions: 810x805mm, max. mould diameter: 804mm, rotary table diameter: 735mm, min. installation height: 300mm, opening stroke: 650mm, opening force: 84kN, tie bar diameter: 80mm, max. daylight opening: 950mm, ejector force: 41.2kN, ejector stroke: 200mm, oil tank volume: 400l, standard drive power: 37kW, hydraulic operating pressure: 240bar, control system: Battenfeld Unilog B4, weight: 7.8t. An on-site inspection is possible.

Injection Moulding Machine

Sumitomo Demag EL-EXIS S 300/720-1450

Germany

2009

used

on request

INNO31486

Clamping force: 3000kN, locking force: 3300kN, max. opening stroke: 670mm, min. mould installation height: 330mm, max. mould installation height: 710mm, max. distance between mould platens: 1380mm, mould platen dimensions: 1040x950mm, distance between tie bars: 720x650mm, max. mould weight: 4.7t, max. weight on moving mould platen: 2.4t, max. weight on fixed mould platen: 3.6t, ejector stroke: 200mm, ejector force: 69kN, ejector return force: 31kN, screw diameter: 50mm, L/D ratio: 20, injection pressure at 400°C: 2426bar, shot volume: 530cm³, shot weight (PS): 480g, max. metering stroke: 270mm, max. nozzle stroke: 470mm, nozzle immersion depth (SVO): 20mm, nozzle contact force: 110kN, installed barrel heating capacity: 14.8kW, material hopper capacity: 110l, oil tank capacity: 700l, electric screw drive: 38kW, electric clamping unit drive: 37kW, pump unit power: 22kW, total installed power: 112kW, continuous sound pressure level: 78dB(A), length: 6500mm, width: 2000mm, height: 2300mm, weight: 15.7t, operating hours according to PLC: 28,890h, barrel heating: 35,656h, pump: 27,922h, documentation available. An on-site inspection is possible.

Injection Moulding Machine

Sumitomo Demag EL EXIS S 200/560-840

Germany

2009

used

on request

INNO31484

Clamping force: 2000kN, locking force: 2200kN, max. opening stroke: 570mm, min. mould installation height: 310mm, max. mould installation height: 660mm, max. distance between mould platens: 1230mm, mould platen dimensions: 830x830mm, distance between tie bars: 560x560mm, max. mould weight: 3.3t, max. weight on moving mould platen: 1.7t, max. weight on fixed mould platen: 2.5t, ejector stroke: 180mm, ejector force: 69kN, ejector return force: 31kN, screw diameter: 45mm, L/D ratio: 20, injection pressure at 400°C: 2402bar, shot volume: 358cm³, shot weight (PS): 330g, max. metering stroke: 225mm, max. nozzle stroke: 400mm, nozzle immersion depth (SVO): 20mm, nozzle contact force: 80kN, installed barrel heating capacity: 13kW, material hopper capacity: 70l, oil tank capacity: 500l, screw drive: 32kW, clamping unit drive: 32kW, pump unit power: 15kW, total installed power: 92kW, continuous sound pressure level: 74dB(A), length: 5700mm, width: 1700mm, height: 2200mm, weight: 11t, operating hours according to PLC: 36,734h, barrel heating: 25,665h, pump: 18,222h, documentation available. An on-site inspection is possible. A Wittmann robotic cell is also optionally available.

Injection Moulding Machine

Mir RMP 200

Germany

1999

used

on request

INNO31423

Ejector stroke: 180mm, ejector force: 44kN, nozzle contact pressure: 38kN, hopper capacity: 75dm³, mold clamping force: 1962kN, mold opening stroke: 560mm, length: 6275mm, width: 1520mm, height: 1965mm, weight: 8.3t. An inspection on site is possible.

Injection Moulding Machine

Engel EM 740/180HL

Germany

2007

used

on request

INNO31387

Clamping force: 1800kN, screw stroke: 200mm, speed: 300rpm, L/D: 20, nozzle stroke: 400mm, nozzle contact force: 50kN, hopper volume: 80l, tie-bar spacing: 520mm/520mm, platen dimensions X/Y: 760mm/760mm, mold installation height range: 250mm-600mm. Machine dimensions X/Y/Z: 6200mm/1700mm/2750mm, weight: approx. 12000kg, operating hours (Nov. 2025): 27271h. Including handling and protective enclosure. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Battenfeld HM 450/3300

Germany

2005

used

on request

INNO31364

Clamping force: 450t, opening stroke: 950mm, tie bar spacing X/Y: 800mm/970mm, operating pressure: 210bar, weight: approx. 20400kg, control system: Unilog B4. An on-site inspection is possible.

Injection Moulding Machine

Ferromatik K-Tec 85

Germany

2000

used

on request

INNO31331

Clamping force: 850kN, tie-bar spacing: 370mm/370mm, platen dimensions X/Y: 540mm/540mm, opening stroke: 450mm, machine dimensions X/Y/Z: approx. 4000mm/1300mm/2000mm, weight: approx. 4250kg. Some parts of the machine have been renewed in recent years. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Battenfeld TM 4500/3300

Germany

2004

used

on request

INNO31159

A large-format horizontal injection molding machine Battenfeld is available. Operating pressure: 210bar, clamping force: 4500kN, screw diameter: 85mm, injection volume: 2128cm³, injection pressure: 1624bar, tie-bar spacing: 900mm/800mm, opening stroke: 950mm, max. mold installation height: 970mm, oil volume: 900l, connected load: 55kW, weight: approx. 20400kg. Documentation available. An on-site inspection is possible. The machine has a defect.

Injection Moulding Machine

Dr. Boy 50T2 185-50

Germany

1992

used

on request

INNO31086

An injection molding machine Dr. Boy is available. Clamping force: 500kN, tie-bar spacing: 305mm/305mm, platen dimensions X/Y: 500mm/500mm, max. opening stroke: 350mm, max. platen spacing: 600mm, min. mold height: 250mm, max. screw stroke: 120mm. Machine dimensions X/Y/Z: approx. 3450mm/1050mm/2000mm, weight: approx. 2050kg, operating hours: 10524h. The system has minor defects requiring repair. Documentation available. An on-site inspection is possible.

Injection Moulding Machine

Engel ES 330/80

Germany

1996

used

on request

INNO30901

Clamping force: 800kN, Opening stroke: 450mm, min. tool installation height: 250mm, Plate dimensions X/Y: 660mm/560mm, Tie bar spacing: 403mm/345mm, Ejector stroke: 100mm, Injection volume: 154cm³, Injection pressure: 1600bar, Machine dimensions X/Y/Z: approx. 6000mm/1850mm/2000mm, Weight: approx. 4900kg. An on-site inspection is possible.

Injection Moulding Machine

Arburg Allrounder 470S 1300-350

Germany

2003

used

on request

INNO30739

Clamping force: 1300kN, screw diameter: 40mm, max. injection pressure: 2120bar, shot volume: 182m³, shot weight: 153g, tie bar spacing: 470mm/470mm, platen dimensions X/Y: 650mm/650mm, min. mold installation height: 275mm, max. opening stroke: 850mm, centering: 125mm. Machine dimensions X/Y/Z: approx. 4600mm/1600mm/2200mm, weight: approx. 5500kg. The clamping unit shows an oil leakage at the clamping cylinder. Documentation available. An on site inspection is possible.

Vertical Injection Moulding Machine

Arburg Allrounder 420C 800-250 VU

Germany

2007

used

on request

INNO30684

A vertical injection molding machine Arburg with a horizontal injection unit is available. Clamping force: 800kN, opening stroke: 500mm, min. mold installation height: 250mm, platen spacing: 750mm, tie bar spacing X/Y: 420mm/420mm, platen dimensions X/Y: 570mm/570mm, max. mold weight: 600kg, ejector stroke: 175mm. Machine dimensions X/Y/Z: approx. 4350mm/1700mm/2100mm, weight: approx. 3500kg. Documentation available. On site inspection is possible.